Flying Leathernecks

Vinyl Mask..

The AERO-3B missile launcher was designed to be used with the AIM-9B Sidewinder missile.This set includes 4 launchers with standoff adapters designed to be used on the Zoukei-Mura F-4C/D/E.Each launcher is 3D printed and come removed from the print supports. All that is needed is a light sandin..

Designed for the Hobbyboss series of kits, enough for one aircraft...

Canopy, wheel mask for Hobbyboss kit..

Set FL48-8014 contains four correct SUU-63A/A wing pylons and one correct SUU-62A/A centerline pylon for the F/A-18A+, A++, C and D.Each set also includes five (5) unlocked BRU-32's and five (5) locked BRU-32's to more accurately depict the different configurations with or without ordnance loaded...

Set FL48-8013 contains four correct SUU-63/A wing pylons and one correct SUU-62/A centerline pylon for the F/A-18A and F/A-18B.Each set also includes five (5) unlocked BRU-32's and five (5) locked BRU-32's to more accurately depict the different configurations with or without ordnance loaded.Th..

3D ResinThis set includes twelve (12) of the larger, swept back antenna typically found on the F/A-18 Hornet. Antenna is also used on other aircraft, so check your references.Can be used on any kit..

Set of four (4) 3D printed launchersThe LAU-7F/A was first introduced in 2008, with more widespread use by 2010. This version is used primarily on USMC F/A-18C/D aircraft...

3D ResinThis set includes two (2) ailerons and two (2) elevators for the Special Hobby kit. These are direct replacements for the multi piece kit parts.CAD by Craig Sargent..

Designed to fit the GBU-31 with Mk-84 warhead included in both the Tamiya F-16CJ and F-15E 'Bunker Buster' kits...

These Missile Launchers are designed to fit the Trumpeter F/A-18E/F wing tip and should work with the Revell kit.Launchers come as shown and only a light sanding of the aft end to remove the support nibs is required. Integrated formation light panel fits into slot on both kit wing tip parts.Fou..

3D ResinThis one piece boarding ladder is designed to fit both the Meng and Hasegawa Super Hornet / Growler kits. May also work with the Revell and Italeri kits, with possible modifications to kit needed.Designed by Richard VanZandt of Flightline Resin, item comes as shown in the photo...

This is a simple replacement for the slightly too thick kit supplied HUD's. Cut in clear .007 styrene, simply cut HUD from runner and apply to kit HUD frame, or any aftermarket photo-etch frame. Enough pieces for six aircraft are included...

This set includes correctly shaped and sized LEX Fence parts applicable to all 1/32 F/A-18A/B/C/D Hornet kits...

3D ResinThis set includes a total of four (4) tail stiffening plates commonly found on F/A-18A and F/A-18A+ Hornets. The four plates will complete two (2) models.3D printed, the plates have all of the rivet and screw fasteners visible. Simply remove from the support, sand the small attachment poin..

3D ResinThis set includes three (3) pieces that make up the belly strap found on late F-4E and all F-4G Phantoms. Designed to be used on the Revell kits, it may work on the Tamiya kit as well.The strap was also found on the F-4S and the F-4J's operated by the UK.Parts come as shown and can be ..

Vinyl Detail..

Waterslide Decals printed by Microscale (Insert printed by Cartograf).8.5 x 11.0 inch sheet..

3D ResinThis set contains one (1) Left Handed AN/AAQ-28 LITENING Pod in the stowed position.Used on USMC F/A-18, EA-6B, Tornado, and TyphoonVery light sanding is required to remove print support nibs from bottom of pod. Comes packaged as shown in the photo.Designed by Sandro Maljic..

Vinyl Mask..

Vinyl Mask..

Vinyl Mask..

Designed to be used with the Fisher Model and Pattern conversion for the Trumpeter A-1H/J..

This set contains four correct SUU-63A/A wing pylons and one correct SUU-62A/A centerline pylon for the F/A-18A+, A++, C and D.These pylons are correct for F/A-18A+ thru D aircraft with BuNo's 163427 thru 163782.This set of pylons corrects the inaccurately shaped pylons included in the Academy k..