Flying Leathernecks

3D ResinAN/ALQ-144, ready to paint and attach to your model.For AH-1W, AH-64A/D/E, UH-1N, H-60, OH-58, VH-3D and OV-10..

3D ResinThis set includes 6 buckets that can be used to replace those found in kits that may be under detailed...

Vinyl Detail..

Vinyl Mask..

This set includes eight (8) corrected Pitot Tubes for use on the F/A-18A thru D, F-14A/B/D, A-7D/E and F-8E.Directly replaces kit parts in the Academy, Tamiya and Trumpeter kitsCAD by Dave Roof..

This set of pylons corrects the inaccurately shaped pylons included in the Academy kit. Each set is 3D printed to ensure the best quality possible, as well as to minimize the work required to prepare them for installation on your model.Sets have been updated and now include separate BRU-32 bomb ra..

This set includes six (6) Mk-83 1000lb bombs with conical fins and six (6) each of the following : M904 nose fuzes, Mk-43 TDD and MXU-735 Nose Plugs.The Mk-83 was the weapon of choice for the USN and USMC during Operation Desert Storm and was used extensively throughout the war. Yours truly built ..

Set of four (4) 3D printed launchersIn January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6.Over the course of the next several years, numerous AAC's changed the designation of the launcher to B/A, A-7, B/A-1, as well as a few others. How..

Set FL172-2000 contains four correct SUU-63/A wing pylons and one correct SUU-62/A centerline pylon for the F/A-18A and B.They not only correct the shape of the kit pylons, they provide details unmatched by the kit supplied parts. All pylons are 3D printed and require little clean up to remove the..

This item includes 2 sets of stiffening plates applied to the left side of each vertical tail on F/A-18A/A+ aircraft in use by the USN, USMC, Canada, Australia and Spain.Made of self adhesive vinyl, they will work with both Academy and Hasegawa 1/72 Kits...

Vinyl..

This set includes three (3) ADM-141 TALD.The TALD was used with great success on SEAD missions in the opening stages of Operation Desert Storm in 1991. More than 100 were launched on the opening night of the war. This prompted the Iraqi air defense to activate many of its radars most of which wer..

This set includes two (2) XM158A1 Rocket Launchers.The Launcher was a seven-tube, reloadable, reusable, repairable 2.75" rocket launcher M158A1 was a variant of the M158 that included a modified hardback mount..

This is a two piece 3D printed set of the SATCOM antenna mounted to the top of the main rotor mast on the UH-1Y Helicopter. Designed for the Kittyhawk kit.Simply glue the antenna to the top center of the base, paint and attach to your model. Parts come ready to install with no clean up required...

Vinyl Mask..

Vinyl Mask..

Vinyl Mask..

Designed for the Monogram kit, enough for one aircraft...

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 5.5 x 8.5 inch sheet..

This set includes the following :Six (6) Thermally Protected Mk-82 500lb bombs with Conical FinsSix (6) M904 Nose FuzesSix (6) MXU-735 Solid Nose PlugsSix (6) Mk-43 TDD Proximity Fuzes (not shown)This bomb/fin configuration is correct for use from Vietnam to Desert StormBombs come as sho..

Mk-77 Fire Bombs, set of four (4)Items are 3D printed and come ready to paint. Some very light sanding of the forward section may be necessary to remove remnants of printing supports.Simply paint natural aluminum and install!..

Vinyl Mask..

This set includes four (4) LAU-7/A-6 AIM-9 launchers designed to fit the pylons in the ZM F-4S. Used from 1988 to 1991..

This set includes four (4) launchers designed to fit the Tamiya F-4 wing pylons in anticipation for later variants. This launcher was used from 1976 to 1987..