Flying Leathernecks

Set includes four (4) launchers.Used to carry two LAU-127E/A or LAU-127A/A for dual AIM-9X / AIM-120B/C carriage..

LAU-115C/A is a rail launcher designed for carriage and launch of AIM-7 missiles from F/A-18 aircraft. The launcher is suspended from the BRU-32 bomb racks in the SUU-63 wing pylons. Two LAU-7 or LAU-127 launchers may be attached to the sides of the LAU-115 for carriage of AIM-9 or AIM-120 missiles...

LAU-115/A is a rail launcher designed for carriage and launch of AIM-7 missiles from F/A-18 aircraft. The launcher is suspended from the BRU-32 bomb racks in the SUU-63 wing pylons. Two LAU-7 or LAU-127 launchers may be attached to the sides of the LAU-115 for carriage of AIM-9 or AIM-120 missiles. ..

3D ResinThis set contains two (2) LAU-10 5.00" rocket pods with empty tubes. Tubes are hollow the whole length of the pod.Designed by Matt Farrow of Shrunk Craft..

Set includes four Mk-82/BLU-111 bombs with rough ablative coating, four KMU-572 kits, which include the tail assemblies and nose strake as separate pieces.Also included are four (4) each : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

Set includes four slick Mk-82/BLU-111 bombs, four KMU-572 kits, which include the tail assemblies and nose strake as separate pieces.Also included are four (4) each : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

Designed to be used with the resin GBU-32 1000lb JDAM produced by Wolfpack Design..

Set includes two Thermally Protected Mk-83 / BLU-110A/B bombs with KMU-559 guidance kit attached and the tail assemblies as separate pieces.Also included are two (2) DSU-33 proximity fuzes, two (2) MXU-735 solid nose plugs and two (2) Ogive nose plugs...

Set includes two Mk-83/BLU-110 bombs with KMU-559 guidance kit attached and the tail assemblies as separate pieces.Also included are two (2) DSU-33 proximity fuzes, two (2) MXU-735 solid nose plugs and two (2) Ogive nose plugs...

3D ResinThis set includes four (4) Thermally Protected GBU-12 laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fi..

3D ResinThis set includes two (2) fuel tanks, made up of four (4) parts each. The nose section, main body, tail cone and a key to line up the nose and main body.Lightly sand the aft surface of the main body to remove the print support nibs, insert key, then attach nose section. Light sanding of th..

3D ResinThis one piece boarding ladder is designed to fit both the Meng and Hasegawa Super Hornet / Growler kits. May also work with the Revell and Italeri kits, with possible modifications to kit needed.Designed by Richard VanZandt of Flightline Resin, item comes as shown in the photo...

Waterslide Decals printed by Microscale (Insert printed by Cartograf).8.5 x 11.0 inch sheet..

Waterslide Decals printed by Microscale.8.5 x 11.0 inch sheet..

This set contains all of the parts necessary to convert the Academy 1/32 F/A-18D into an ATARS Configured aircraft. The Advanced Tactical Airborne Reconnaissance System (ATARS) had its combat debut in 1999 with VMFA(AW)-332 during Operation Allied Force and continued to see service throughout Operat..

Waterslide Decals printed by Microscale.8.5 x 11.0 inch sheet..

Vinyl Mask..

Waterslide Decals printed by Microscale (Insert printed by Cartograf).8.5 x 11.0 inch sheet..

This is a simple replacement for the slightly too thick kit supplied HUD's. Cut in clear .007 styrene, simply cut HUD from runner and apply to kit HUD frame, or any aftermarket photo-etch frame. Enough pieces for six aircraft are included...