Flying Leathernecks

Set of four (4) 3D printed launchersIn September of 1976, AAC 688 introduced a new dual Fin Retaining Clip for the new AIM-9L Sidewinder, creating the LAU-7/A-4.In June of 1980, AAC-736 was introduced and the launcher became the LAU-7/A-5.The LAU-7/A-5 was the launcher used when two VF-41 F-14..

Set of four (4) 3D printed launchersIn May of 1969, AAC 545 introduced the Fin Retaining Clip for the AIM-9D/G/H Sidewinder, creating the LAU-7/A-1.In January of 1971, AAC-537-1 introduced the Detent Holdback Pin, creating the LAU-7/A-2.By 1972, the launcher was re-designated as the LAU-7/A-3 ..

Set of four (4) 3D printed launchersThe LAU-7/A was developed in June of 1958 for use on the F4H-1 (F-4B) and designed to be used with the AIM-9B missile. This version was in service until May of 1969 when AAC-545 was introduced.Our sincere thanks to Gerry Whiteside and Bill Arndt for their ass..

3D ResinThis set includes six (6) highly detailed and accurate IFR probe tips for use on all US and NATO aircraft that use the hose and drogue system...

Vinyl Mask..

Vinyl Mask..

This set contains pre-cut self adhesive vinyl Det Cords for the forward and aft canopies. Designed to fit the Kinetic / Wolfpack Design kits.Transfer tape included and pre-attached...

Canopy, radome, wheel mask for Italeri / ESCI / AMT kits..

This set is designed to fit inside the kit and force the bottom seam into the proper position and allow easy gluing and seam work...

This set includes four (4) Mk-84 2000lb bombs with four (4) Conical fins and six (6) each of the following : M904 nose fuzes, Mk-43 TDD and MXU-735 Nose Plugs.The Mk-84 was used extensively by the USMC during Operation Desert Storm...

This set includes four (4) Mk-83 1000lb bombs with the Thermal Protective coating, four (4) Conical fins and four (4) each of the following : M904 nose fuzes, Mk-43 TDD and MXU-735 Nose Plugs.The Mk-83 was the weapon of choice for the USN and USMC during Operation Desert Storm and was used extensi..

This set includes four (4) Mk-83 1000lb bombs with the Thermal Protective coating, four (4) BSU-85 fins and four (4) each of the following : M904 nose fuzes, Mk-43 TDD and MXU-735 Nose Plugs.The Mk-83 was the weapon of choice for the USN and USMC during Operation Desert Storm and was used extensiv..

This set includes the following :Six (6) Mk-82 500lb bombs with Conical FinsSix (6) M904 Nose FuzesSix (6) Ogive Nose PlugsSix (6) MXU-735 Solid Nose PlugsSix (6) Mk-43 TDD Proximity Fuzes (not shown)This bomb/fin configuration is correct for use from Vietnam to Desert StormBombs come ..

While we have an extensive line of ordnance, we also understand that some modelers are perfectly content using the bombs provided in the kits. In some cases, the fuzes included with them leave a lot to be desired.This set provides 24 M904 nose fuses that will help enhance those kit supplied bombs..

This set includes the detonation cords for the forward and aft canopy pre-cut in self adhesive gray vinyl. Designed to fit the canopy of the Kinetic kit...

In February of 1964, the LAU-7A/A was introduced as a USAF version of the LAU-7/A that incorporated provisions for launching the TDU-11/B Target Rocket.The LAU-7A/A was used interchangeably with the Aero-3B on USAF F-4C/D/E Phantoms.The standoff adapters in this set are designed to fit the Zouke..

In January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6.Over the course of the next several years, numerous AAC's changed the designation of the launcher to B/A, A-7, B/A-1, as well as a few others. However, all of these changes were either..

This set includes four (4) empty LAU-68F/A pods. The F/A is 11 inches longer than the LAU-68D/A and is used exclusively with the 2.75 APKWS rockets. Pod is used by the F/A-18, AV-8B, AH-1Z, UH-1Y, A-10, F-16 and a number of other aircraft.Rocket tubes are hollow the entire length of the pod to dep..

Designed by Petr Haupt, this set includes two (2) LAU-33 Pods, four (4) Mk-71 Rocket Motors, four (4) Mk32 Mod 0 anti tank / anti personnel warheads with Mk188 Impact Fuzes and four (4) Mk32 Mod 0 warheads with Mk93 proximity fuzes..

This set includes four (4) missile launchers in medium gray 3D printed resin.Missiles come as shown with print supports removed. Some very minor sanding to smooth areas where supports were located may be necessary.Launchers designed by Richard VanZandt of Flight Line Resin..

These Missile Launchers are designed to fit the Hasegawa F/A-18E/F wing tip and work perfectly with the Meng kit with one small modification to the kit part.Launchers come as shown and only a light sanding of the aft end to remove the support nibs is required. Integrated formation light panel fit..

These Missile Launchers are designed to fit the Hasegawa F/A-18E/F wing tip and work perfectly with the Meng kit with one small modification to the kit part.Launchers come as shown and only a light sanding of the aft end to remove the support nibs is required. Integrated formation light panel fit..

Set includes four (4) launchersUse for early F/A-18E/F..

Set includes four (4) launchersUsed to carry and launch AIM-9X and AIM-120B/C..