Hypersonic Models

This is a set of full-length and correctly angled jet exhaust tailpipes for the A-6 Intruder family (A-6A, A-6E, A-6E TRAM, EA-6A). It contains detailed, thin-edged nozzles as well as detailed J-52 engine end with guide vanes and probes. The set is designed for the HobbyBoss Intruder kits (and the i..

This is a cockpit set for Kitty Hawk's FJ-2 Fury kit (1:48). It includes a corrected and detailed seat with parachute and harness in place, a detailed rear cockpit bulkhead and turtle deck, the FJ-2 specific loop antenna assembly as well as a detailed canopy rear deck...

F-4 Phantom C/L pylon, 1:48, for the Tamiya line of kits. The pylon fits on and into the moulded-on mounting tab between the Aux doors on Tamiya's kit with a simple modification (it needs to be shortened and slightly re-shaped). The pylon set comes with two sets of separate pins - one for the larger..

This is a full conversion set to build an NF-104A aerospace/astronaut trainer aircraft from the Kinetic F-104G kit. The set comes with all parts needed, some injection moulded plastic, some 3D printed, plus a turned brass pitot boom and a full set of decals by Caracal (printed by Cartograf)...

Corrected tail surfaces (stabilisers, elevators and rudder) for the Kitty Hawk FJ-2 Fury (and early FJ-3). The FJ-2 kit only contains the ribbed elevators/rudder, which is correct for an FJ-3 and very late FJ-2's after transfer to the Reserves. FJ-2's in service (as well as early FJ-3's) had smooth-..

Corrected A/C air intakes for Academy's F-4 Phantom series (F-4B, C and D so far). Drop fit resin replacement. All it takes is a little superglue and a swipe of filler to blend it in...

Decals for F-15E that took part in the operation Odyssey Dawn, Libya 2011. Features two aircraft, 97-0219 and 01-2003. Markings include full crew names that were re-applied after the operation, full contemporary stencils and landing gear placards. The set comes with paint masks for insignia, ID mark..

This conversion set includes the AN/ANQ-126 fairings for the intakes (with mounting holes to match Tamiya's moulded-on pins), a fin cap with the correct sensor bulge for the N model, a new RIO instrument panel and an external rear view mirror. Further N specific parts are already included in the Tam..

This set contains a pair of 1:72 outer wing pylons with weapons adapters for USN and USMC Phantoms (and some early USAF ones as well). Suitable for all brands of 1:72 Phantom kits...

This is an empty SR-71 brake chute bay with open doors, as commonly seen after landing. Designed specifically for the Revell kit. The set comes in four 3D printed parts: the main bay, a separate end cap (for easier painting) and separate doors. The door parts have mounting lips and recesses designed..

This is a set of highly detailed and appropriately proportioned stick/grip and throttle for the Kinetic F-104 kits in 1:48. The kit parts are both oversized and a bit sparse in detail. These 3D printed resin parts are drop-in replacements that fit right into the kit's mounting holes. The parts fit b..

A set of two Martin Baker Mk. H5 ejection seats for early F-4B, F-4C and F-4D Phantoms (until around 1970). Suitable for and tested with Academy, Hasegawa and Zoukei Mura kits. The seats have cast on seat belts which differ from each other...

This is a replacement nose landing gear strut for Kitty Hawk's FJ-2 and FJ-3 Fury kits. The lower yoke is cast in brass in one piece (much stronger than the original) and corrects the misshapen kit part. The upper strut is cast in resin, with added and refined detail and has a nickel-silver rod cast..

This is a slat-wing conversion set for the Zoukei Mura F-4E (early), hard wing kit. This set contains slatted outer wings (cast in a special hard resin to prevent warping) and inboard slat inserts. No cutting is required for installation. In addition, the set contains a multi-part belly reinforcemen..

Full set of late type T-38 wheels including two types of nose wheels and brake detail. The late type main wheels are punched and have different brake detail to the early type. Suitable for T-38A and T-38C and designed for the Wolfpack kit, but may fit other kits...

Full set of early type T-38 wheels including brake detail and two types of nose wheels. The early main wheels had plain disk shaped rims without holes and the brake configuration was different from the later type. Suitable for the T-38A, designed for the Wolfpack kit, but may fit others...

Corrected (re-shaped and re-framed) canopy for the Trumpeter Skywarrior kits in 1:48. Escape hatch may be posed open. Applicable to EA-3 , RA-3, and ERA-3 types...

Corrected (re-shaped and re-framed) canopy for the Trumpeter Skywarrior kits in 1:48. Escape hatch may be posed open. Applicable to EA-3 , RA-3, and ERA-3 types...

A pair (2) of early McDonnell type 370gal wing drop tanks for F-4 Phantoms. Mainly applicable for early Phantoms such as F4H-1/F-4B/C/D, but seen as late as 1973 on an F-4J. Separate, handed pylons are included. Use with any 1:72 Phantom kit...

A pair (2) of early McDonnell type 370gal wing drop tanks for F-4 Phantoms. Mainly applicable for early Phantoms such as F4H-1/F-4B/C/D, but seen as late as 1973 on an F-4J. Separate, handed pylons are included. The pylons for Hasegawa kits will fit both their thick (C/D/J) and their old raised pane..

A pair (2) of early McDonnell type 370gal wing drop tanks for F-4 Phantoms. Mainly applicable for early Phantoms such as F4H-1/F-4B/C/D, but seen as late as 1973 on an F-4J...

A pair (2) of early McDonnell type 370gal wing drop tanks for F-4 Phantoms. Mainly applicable for early Phantoms such as F4H-1/F-4B/C/D, but seen as late as 1973 on an F-4J...

The is an accurate 1:48 nose wheel/gear door for early A-4 Skyhawks, such as A-4B and A-4C. Designed for Hasegawa kits. The door differs in a lot of detail from the kit supplied later type door. A very minor modification is required on the edge of the nose gear bay of the kit...

..