Hypersonic Models

This is an update set for ClearProp's D-21 kit. It contains more detailed and more accurate engine sets (with one-piece nozzle), intake with one-piece spike, new back plate and better proportioned pitot and a camera to go behind the glass...

This is a resin Canberra PR.9 and B(I)8 canopy in 1:48 scale with the correct circular cross section that replaces the Airfix canopy which has an incorrect "U" cross section. As the correct cross section is circular, the offset position makes it "tuck under" on the left side and that is not represen..

This is a set of 3D printed B-26K (A-26A) Counter Invader / Nimrod wheels. For the ICM kit in 1:48. The mounting points are designed for a direct fit to the kit axles. The wheel hubs are loaded with fine and accurate detail, from valve stems to visible springs in the brake pads. The tyres have very ..

Full injection moulded plastic kit of one AG-330 start cart for the famous Blackbird family of planes (A-12, YF-12, M-21 and SR-71). Optional parts for both an early "Buick" powered, or the later "Chevy" powered cart are included. The starter probe can be built retracted or extended. Photo etched de..

This is a set of two individually detailed Martin Baker Mk. GRU5 seats in 1:48 for A-6A, EA-6A and A-6E Intruders (used until about the mid 70s, when replaced by the GRU7), designed and sized for the Hobby Boss cockpit. I can't say if it will fit the Revell EA-6A. The belt and hose arrangement is di..

This is an airframe update set for Kitty Hawk's FJ-2 Fury. It includes a new intake nose ring with a corrected shape (the kit's nose is much too blunt) and cast-on one-piece air intake front part. There is detail scribing on the inside of the nose ring (absent on the kit parts). The nose wheel well ..

F-4 Phantom C/L pylon, 1:48, for the Zoukei Mura line of kits. The pylon fit on and into the detail moulded onto the ZM lower wing surface. It comes with two sets of separate pins - one for the larger stabiliser pins and the smaller sway brace pins that connect to the stores to be mounted...

F-4 Phantom C/L pylon, 1:48, for the Tamiya line of kits. The pylon fits on and into the moulded-on mounting tab between the Aux doors on Tamiya's kit with a simple modification (it needs to be shortened and slightly re-shaped). The pylon set comes with two sets of separate pins - one for the larger..

A pair (2) of early McDonnell type 370gal wing drop tanks for F-4 Phantoms. Mainly applicable for early Phantoms such as F4H-1/F-4B/C/(D), but seen as late as 1973 on an F-4J. Separate, handed pylons are included. The tanks are cast in hollow halves that are very easy to clean up and assemble...

This is a centreline pylon for Kinetic's F-104 series, suitable for variants from C through to S. The item is 3D printed and packed with detailed features. The outer sway braces are fixed, while the two centre pads are separate pieces that can be adjusted to match the loadout being mounted. The pylo..

These are 3D printed face curtain handles for MB Phantom ejection seats. The handles are mainly designed for the Hypersonic Models Mk. H5 seats but can be used on other types (H7) and manufacturer's seats as well. The handles are 3D printed but from a slightly elasctic resin that doesn't break as ea..

This is an empty SR-71 brake chute bay with open doors, as commonly seen after landing. Designed specifically for the Revell kit. The set comes in four 3D printed parts: the main bay, a separate end cap (for easier painting) and separate doors. The door parts have mounting lips and recesses designed..

This set contains the parts needed to build an accurate late type F-104A from the Kinetic F-104A/C kit. "Late" means that it's an airframe that was converted to the upward firing C-2 seat. Therefore you can either use the kit supplied seat or one of the various available aftermarket options.The pa..

This is a set of highly detailed and appropriately proportioned stick/grip and throttle for the Kinetic F-104 kits in 1:48. The kit parts are both oversized and a bit sparse in detail. These 3D printed resin parts are drop-in replacements that fit right into the kit's mounting holes. The parts fit b..

This is a set of highly detailed and appropriately proportioned stick/grip and throttle for the Kinetic F-104 kits in 1:48. The kit parts are both oversized and a bit sparse in detail. These 3D printed resin parts are drop-in replacements that fit right into the kit's mounting holes. The parts fit b..

This is a set of two aft canopy braces for Kinetic F-104 Starfighter kits. This part is applicable to all F-104 single seat variants and is not provided in any of the Kinetic's kits. The part is very delicate, but printed from slightly forgiving resin for safer support removal and handling...

This is a TISEO pod for the Meng F-4E kit, 1:48. The pod parts are 3D printed and the glass is a cast clear resin piece. A paint mask is provided as well...

This is a set of Navy type outer wing pylons designed to fit the Zoukei Mura Phantoms (J and S). The set comes with separate sway brace pins so the modeller can adapt them completely free to the specific store and correct outboard angle (in case of MER or TER installed). The photos show the pylon bo..

Here is full set of resin wheels for Revell's 1:48 SR-71 kit. The wheels come with all correct detail, including brake detail and even the brake line connectors on the main wheel hubs. The anti-skid generator brackets are provided as delicate photo etch parts. The main wheels are NOT two identical s..

This is an upgrade set for the stabilator area of the Tamiya F-4 Phantom kit(s). It replaces the kit's overly thick stabiltor cover plates and guide tracks with much thinner and more detailed PE parts. At the same time, you will also install the kit's separate lower tail insert module early on. You ..

This is an IRST equipped chin (radome) pod for early F-4B's, specifically for the Tamiya kit. While not from the very start of production deliveries, F-4B's were fitted with this Infra-red Search and Track system from ca. 1962. The pod in the Tamiya kit is the late type, having a longer non-IRST for..

This is a set of two SR-1 seats for the new Revell 1:48 SR-71. The seats are very accurate in dimension and detail and have been fully CAD designed. The two seats in the set are not identical in the draping/positioning of the belts and hoses. One modification to a detail on the seat was made to adap..

The early/narrow tyres in the Hasegawa kit are too wide. These new tyres are narrower, have deep tread detail and are very subtly bulged. Use these tyres with both the early and late style wheel hubs with all operators EXCEPT German, Italian and other Euro-NATO AF's that used the G model - or in oth..