All Products

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

Water-slide Decals: Instruction: 1.Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them. 2.Cut out the decal you need (do it on cutting mat) 3.Grab the decal wit..

Water-slide Decals: Instruction: 1.Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them. 2.Cut out the decal you need (do it on cutting mat) 3.Grab the decal wit..

Product Type: 3D Decals Equipment Type: Seats (not included)3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - A..

Product Type: 3D Decals Equipment Type: Seats (not included)3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - A..

Set contains 3D-printed parts to build 1 engine "Wright R-2600 Twin Cyclone" in scale 1/72.Applications: Boeing 314 Clipper, Brewster SB2A Buccaneer, Curtiss SB2C Helldiver, Douglas A-20 Havoc, Douglas B-23 Dragon, Grumman F6F Hellcat, Grumman TBF Avenger, Liore et Olivier LeO 451, Martin Baltimor..

How-to:Preparing the masks: Masks should not be stretched during the application process as they are flexible and this could cause deformation. Remove the whole mask if necessary, and then apply again. Once placed on the model, the mask surface should be adjusted to the surface of the model by traci..

How-to:Preparing the masks: Masks should not be stretched during the application process as they are flexible and this could cause deformation. Remove the whole mask if necessary, and then apply again. Once placed on the model, the mask surface should be adjusted to the surface of the model by traci..

Products made in 3D are not assembled or painted, and colour differences may occur depending on the resin used.Experience in removing 3D parts can be helpful but is not essential. Any supports attached to the detailed areas can be cut with side cutters or a slitting disc, and the remaining parts c..

Products made in 3D are not assembled or painted, and colour differences may occur depending on the resin used.Experience in removing 3D parts can be helpful but is not essential. Any supports attached to the detailed areas can be cut with side cutters or a slitting disc, and the remaining parts c..

Set contains 3D-printed parts for detailing of propellers for the aircraft model PV-1 Ventura...

** This model kit is supplied in unassembled and unpainted resin components. Please note that glue, model paints, and other basic modelling tools are required and sold separately...

..

Product Type: 3D Decals Equipment Type: Seats (not included)3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - A..

Paint Mask:Preparing the masks: Masks should not be stretched during the application process as they are flexible and this could cause deformation. Remove the whole mask if necessary, and then apply again. Once placed on the model, the mask surface should be adjusted to the surface of the model ..

Set contains resin parts to assemble 2 inlet cones...

unassembled and unpainted..

Set contains 3D-printed parts and coloured seat belts to build 2 seats KM-1M...

How-to:Preparing the masks: Masks should not be stretched during the application process as they are flexible and this could cause deformation. Remove the whole mask if necessary, and then apply again. Once placed on the model, the mask surface should be adjusted to the surface of the model by traci..

Set contains 3D-printed parts for detailing of propellers for the aircraft model Gotha Go 244B (Italeri)...

Set contains 3D-printed parts to build 2 engines ''Gnome-Rhone 14N'' in scale 1/72.Applications: Amiot 351, Amiot 354, Bloch MB.131, Bloch MB.135, Bloch MB.150, Bloch MB.151, Bloch MB.152, Bloch MB.155, Bloch MB.161, Bloch MB.170, Bloch MB.174, Bloch MB.175, Bloch MB.210, Bloch MB.220, Bloch MB.30..