All Products

Cast resin model of British experimental tailless aircraft developed during WW2. The HP. 75 Manx was built to evaluate flight characteristics for much larger tailless aircraft to be used as a military bomber. The plane flew with two types of engine cowlings and undercarriage legs. The model contains..

Full-resin model of 1930's British fighter prototype. Although Gloster F.5/34 offered quite good performance, production of Hurricanes and Spitfires started up faster. Two prototypes were test-flown until the mid of the war. The model consists of detailed cast resin parts, vacuum formed canopy, deca..

Set contains five figures of German Tank Crew dated 1944. The figures are intended to be placed into crew entry hatches therefore they're sculpted in half body configuration...

Set contains three figures of German Tank Crew dated 1944. The set contains complete standing figures...

Set contains new three sitting figures of WWII German Tank Crew...

This set brings completely new main undercarriage wheels. The master parts were created using 3D and produced on a 3D printer. The wheels offer much higher levels of detail than the original parts, tyres come with better tread pattern. Can be used with any ICM's Fw 189 kit, i.e. A-1, A-2 and A-1 Nig..

Even such a nice kit as the new ICM Fw 189A no doubt is has its small flaws. One of them obviously is the incorrectly shaped engine nacelle air intakes. Our set offers you new front sections of the nacelles into which just fit another resin parts portraying the front pairs of Argus As 410 engine cyl..

The new ICM Fw 189A kit has wrong-shaped propeller blades and the spinners with ''windmills'', ie pitch control vanes. Now we offer a set of new blades with correct dimensons and also the spinners with better windmills...

This set with a pilot and two ground crew members has been prepared specially for the new Mirage F.1 model..

Lovely little renditions of the Fouga wheels that can adorn not only our new Special Hobby model, but could also be used with older Airfix, Heller or Valom kits...

Impressive resin seats designed to enliven models of the Fouga Magister, one of the most commonly used jet trainer aircraft of the last century...

The WOT2 lightweight lorry was produced by the British Ford factory at Dagenham from 1939 in several varieties. Almost 60,000 of these vehicles were built in total throughout the war, and they remained in service with the Army, RAF and RN well until the end of the 1950s. During the war, these machin..

..

Weighted tyres wheel with nice details designed for the new Heller's E-2 Hawkeye kit...

New control surfaces (ailerons, wing flaps, rudder and elevators) which can be attached to the model in deployed position. Designed to fit the new Special Hobby models...

The Dornier Do 27 kit will benefit from the addition of nicely detailed pilot and passenger seats with seat belts and two styles of the instrument panels. The set contains photo etched seat belts and a instrument faces pre-printed on a piece of clear film...

A triplet of civilian figures that could enliven any model of a post-war German aeroplane. The pilot is joined by a photographer carrying two cameras and a figure of a female zoologist. Not just for the Special Hobby Dornier Do 27, in fact any other 1/72 non-military aircraft or vehicle will enjoy t..

In this set, we bring the modeller three standing figures of Czechoslovak pilots from the 1930s. The figures could also be used to portray WW2 Slovak State airmen. Beautiful addition to such model kits as Special Hobby Letov S.328, Eduard Avia B.534 and others...

These detailed figures of two mechanics at work and one pilot were prepared to accompany the new eduard MiG-15 kit, but also for other Warsaw Pact contemporaries. The clothing sets these figures back in to the 1950s...

Contains four 9x16 wheels for WW2 British, and other Commonwealth armies’ truck (Lorry)...

Contains four 9x16 wheels for WW2 British, and other Commonwealth armies’ truck (Lorry)...

The CASA C-212 cargo and transport aircraft feature double-slotted flap wings giving them excellent STOL capability. This set consists of these double-slotted flaps in their down position and is designed for the Special Hobby kit. It comes also with the wing internal structure and the flap hinges...

Full resin kit of prototype of French jet VTOL plane with annular wing. The model consists of resin parts, vacuum formed clear parts, white-metal u/c legs and decals...

The set offers completely new main undercarriage wheels to accompany any version of the F2A Buffalo fighter kit. 3D designed, 3D printer produced master parts...