Model Planes

This is a resin model kit, which comes unassembled and unpainted. So glue, model paints and other basic modelling tools are additionally required...

..

3D ResinThis is a two piece 3D printed set of the SATCOM antenna mounted to the top of the main rotor mast on the UH-1Y Helicopter.Simply glue the antenna to the top center of the base, paint and attach to your model. Parts come ready to install with no clean up required...

..

..

3D ResinSet of four (4) 3D printed launchersIn January of 1987, AAC-829 was introduced and by May of 1988, over 6500 launchers had been modified to LAU-7/A-6.Over the course of the next several years, numerous AAC's changed the designation of the launcher to B/A, A-7, B/A-1, as well as a few oth..

3D ResinThis set includes two empty LAU-68F/A pods. The F/A is 11 inches longer than the LAU-68D/A and is used exclusively with the 2.75 APKWS rockets. Pod is used by the F/A-18, AV-8B, AH-1Z, UH-1Y, A-10, F-16 and a number of other aircraft.Pods are 3D printed and come ready to paint and attach t..

3D Resin..

3D ResinThis set contains two (2) LAU-10 5.00" rocket pods with empty tubes. Tubes are hollow the whole length of the pod.Designed by Matt Farrow of Shrunk Craft..

3D ResinThis set includes six (6) SATCOM Antenna with short mount found on a number of Helicopters. Use fine sprue cutters to remove part from support and lightly sand base smooth. Attach using super glue (CA)...

3D ResinAN/ALQ-144, ready to paint and attach to your model.For AH-1W, AH-64A/D/E, UH-1N, H-60, OH-58, VH-3D and OV-10..

3D ResinThis set includes 6 buckets that can be used to replace those found in kits that may be under detailed...

3D ResinThis set includes six (6) buckets that can be used in a diorama setting (ordnance loading evolution) or to replace kit parts...

Vinyl Detail..

3D ResinThis detailed TSS is a direct replacement for the kit parts. Simply detail paint and install.Use sprue cutters to remove turret from supports and lightly sand support nibs smooth. It may be necessary to remove the locating tabs from kit parts C59 and C60..

3D ResinThe FMV Mod fitted to the tail boom of the AH-1Z and UH-1Y allows grounds units to see what the aircrew sees through the aircraft's FLIR.Designed for the Academy kit..

Interior and ExteriorThe set includes one sheet of masks (shown in the picture). The masks are made from thin masking tape, which is easy to be peeled off and doesn't leave any stains. The tape is tested on clear and painted model too. If carefully removed after painting, they can be used over and..

3D ResinThis set includes four (4) ADU-299 Adapters. These are used to allow aircraft to carry the LAU-7 missile launcher on stations not normally designed to carry that launcher...

A6M2 Zero Fighter includes the interior of the Engine and Weapons** This model kit is supplied in unassembled and unpainted plastic components. Please note that glue, model paints, and other basic modelling tools are required and sold separately...

..

..

..

Suggested kit: Supermarine Spitfire kits in 32nd scaleRe-usable die-cut paint masksThe set includes one sheet of pre-cut masks (shown in the picture). The masks are made from thin masking tape, which is easy to be peeled off and doesn't leave any stains. The tape is tested on clear and painted m..

The set includes two sheet of masks (shown in the picture). The masks are made from thin masking tape, which is easy to be peeled off and doesn't leave any stains. The tape is tested on clear and painted model too. If carefully removed after painting, they can be used over and over again. It is flex..