Model Planes

Set includes two (2) Thermally Protected Mk-83/BLU-110 bombs with KMU-559 guidance kit attached and the tail assemblies as separate pieces.Also included are two (2) DSU-33 proximity fuzes, two (2) MXU-735 solid nose plugs and two (2) Ogive nose plugs...

The FPU-6/A Oval Fuel Tank was developed for the F/A-18A/B Hornet in 1978 and used on the FSD aircraft, as well as a few fleet Hornets into the mid 1980's. It was phased out due to fatigue anomalies caused by the oval configuration.This set includes two hollow tanks that require assembly. Some li..

Wheels designed to fit the Kinetic F/A-18A/B/C/D Hornet Kits..

3D ResinThis set contains one (1) Right Handed AN/AAQ-28 LITENING Pod in the stowed position.Used on USMC F/A-18, EA-6B, Tornado, and TyphoonVery light sanding is required to remove print support nibs from bottom of pod. Comes packaged as shown in the photo.Designed by Sandro Maljic..

The AERO-3B missile launcher was designed to be used with the AIM-9B Sidewinder missile.This set includes 4 launchers with standoff adapters designed to be used on the Zoukei-Mura F-4C/D/E.Each launcher is 3D printed and come removed from the print supports. All that is needed is a light sandin..

Set FL48-8014 contains four correct SUU-63A/A wing pylons and one correct SUU-62A/A centerline pylon for the F/A-18A+, A++, C and D.Each set also includes five (5) unlocked BRU-32's and five (5) locked BRU-32's to more accurately depict the different configurations with or without ordnance loaded...

Set of four (4) 3D printed launchersThe LAU-7F/A was first introduced in 2008, with more widespread use by 2010. This version is used primarily on USMC F/A-18C/D aircraft...

These Missile Launchers are designed to fit the Trumpeter F/A-18E/F wing tip and should work with the Revell kit.Launchers come as shown and only a light sanding of the aft end to remove the support nibs is required. Integrated formation light panel fits into slot on both kit wing tip parts.Fou..

3D ResinThis set contains one (1) Left Handed AN/AAQ-28 LITENING Pod in the stowed position.Used on USMC F/A-18, EA-6B, Tornado, and TyphoonVery light sanding is required to remove print support nibs from bottom of pod. Comes packaged as shown in the photo.Designed by Sandro Maljic..

..

3D printed air-to-surface / anti-tanks missile recommended for helicopters such Alouette II, Alouette III, Scout, UH-1B Huey etc. kits..

3D printed air-to-surface / anti-tanks missile recommended for helicopters such Alouette II, Alouette III, Scout, UH-1B Huey etc. kits..

High quality print. Includes two pcs. of the machine gun...

..

..

Type: Turned Metal PartsIncluded Items:- 2x Barrels for Mk 103- 2x Muzzle Brakes- 1x Pitot Tube..

Collaboration with Aber...

..

..

..

..

3D-printed ammunition magazines for the MG 15, of the typical bean-shaped form. These were usually placed in the reach of the gunners, but very often are missing in the model kits or lack much detail. Our printed P72034 set replaces the already not available CMK Q72139 resin cast set. The new one al..

..

The MG15 machine gun, developed in the 1930s by the Rheinmetall-Borsig company, became the standard Luftwaffe machine gun. It was widely used as a hand-manipulated weapon in various Luftwaffe aircraft types, including the He 111, Ju 86, and early Ju 88s. However, in 1942, the new MG81 began to gradu..