Model Planes

This set contains six (6) Mk-82 500lb bombs with BSU-86 retarded fins. Also included are six (6) each of the following :M904 Nose FuzeMk-43 TDDMXU-735 Solid Nose PlugBombs come as shown in the photo. Light sanding may be needed on the aft end of the tail section to remove remnants of suppor..

This set contains six (6) Mk-82 500lb bombs with thermal protective coating and BSU-86 retarded fins. Also included are six (6) each of the following :M904 Nose FuzeMk-43 TDDMXU-735 Solid Nose PlugBombs come as shown in the photo. Light sanding may be needed on the aft end of the tail secti..

3D ResinThis set includes six (6) Mk-82 500lb Bombs with BSU-49 Ballute Tail Fins, Six (6) M904 Nose Fuzes, Six (6), DSU-33 Proximity Fuzes and Six (6) USAF Nose Plugs.This Tail Fin is primarily used by the USAFTo allow for maximum detail on the aft end of the tail, this item is supported from ..

This set includes six Thermally Protected Mk-82 / BLU-111/B bombs with BSU-33/B tail fins, and six each of the following : M904 nose fuzes, Mk-43 TDD, MXU-735 nose plugs.Accurately reproduced using personal measurements and photos of the real item. Parts come as seen in the photo, leaving minimal ..

This set includes six Mk-82 / BLU-111/B bombs with BSU-33/B tail fins, and six each of the following : M904 nose fuzes, Mk-43 TDD, MXU-735 nose plugs.Accurately reproduced using personal measurements and photos of the real item. Parts come as seen in the photo, leaving minimal work for the modeler..

Mk-76 practice bombs (12 per pack)These new 3D printed bombs come ready to paint and install. Some very light clean up may be necessary at the aft end of the fins to remove any trace of the printing supports.Simply paint FS35109 Blue and install!..

While we have an extensive line of ordnance, we also understand that some modelers are perfectly content using the bombs provided in the kits. In some cases, the fuzes included with them leave a lot to be desired and may not be what you'd like to depict.This set provides 24 Mk-43 TDD (Target Dete..

3D Resin..

Set of 4 LAU-7 Missile Launchers designed to be used on the Zoukei-Mura F-4J. With little modification, can also be used on the Academy F-4J and Hasegawa F-4JOur sincere thanks to Gerry Whiteside and Bill Arndt for their assistance with research.Master CAD files produced by Richard VanZandt..

Set of 4 LAU-7 Missile Launchers designed to be used on the Zoukei-Mura F-4J. With little modification, can also be used on the Academy F-4B/N/J, Hasegawa F-4B/N/J and Tamiya F-4B.Our sincere thanks to Gerry Whiteside and Bill Arndt for their assistance with research.Master CAD files produced by..

This set includes four (4) LAU-33 dual 5.00" Rocket Launchers with empty tubes.Used by the F-4 Phantom, F-8 Crusader, OV-10 Bronco..

This set contains two (2) LAU-10 launchers with full length hollow tubes.Designed by M. Farrow of Shrunk Craft..

Set includes four (4) Mk-82/BLU-111 bombs with the rough ablative coating, four (4) KMU-572 tail assemblies attached and the nose strake as separate pieces.Also included are four (4) each of the following : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

Set includes four (4) Mk-82/BLU-111 bombs with KMU-572 tail assemblies attached and the nose strake as a separate piece.Also included are four (4) each of the following : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

This set includes four (4) GBU-16 Thermally Protected laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fins in th..

This set includes four (4) GBU-16 laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fins in the guidance section u..

This set includes four (4) GBU-12 laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fins in the guidance section u..

Wheels designed to fit the Hasegawa F/A-18A/B/C/D Hornet Kits..

3D ResinThis set includes twenty four (24) DSU-33 Proximity Fuzes. These are designed to work with all kit supplied bombs that may not have accurate or clean versions...

3D ResinThis set includes one travel pod for use on all USN/USMC F-4 Phantom kits..

This set includes four (4) BDU-57 / 59 / 60 Laser Guided Training Rounds with separate seeker heads.Careful removal of parts from print supports and minimal clean up required.Can be used with the F-14A/B/D, F/A-18A/B/C/D/E/F and AV-8B..

3D ResinThis set includes twelve (12) BDU-33 25lb practice bombs...

This set includes eight (8) wing pylons, one (1) centerline pylon, seven (7) BRU-36 ejector racks, and two (2) LAU-138 BOL launchers.3D printed and designed by Richard VanZandt using photos and measurements provided by FLD, Simon Oakes, Robert Foster and David Sweetman..

This set includes 6 buckets that can be used to replace those found in kits that may be under detailed...