Model Planes

Set includes two Mk-83/BLU-110 bombs with KMU-559 guidance kit attached and the tail assemblies as separate pieces.Also included are two (2) DSU-33 proximity fuzes, two (2) MXU-735 solid nose plugs and two (2) Ogive nose plugs...

3D ResinThis set includes four (4) Thermally Protected GBU-12 laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fi..

3D ResinThis set includes two (2) fuel tanks, made up of four (4) parts each. The nose section, main body, tail cone and a key to line up the nose and main body.Lightly sand the aft surface of the main body to remove the print support nibs, insert key, then attach nose section. Light sanding of th..

This set includes four (4) highly detailed ADU-703 adapters with BRU-32 bomb racks for use on the Tamiya, Revell and Trumpeter 1/32 F-14A/B/D kits. Modification to the kit weapons rails will be necessary. Drawings with measurements on where to cut are provided.Released in cooperation with our frie..

3D ResinThis set includes twenty four (24) DSU-33 Proximity Fuzes. These are designed to work with all kit supplied bombs that may not have accurate or clean versions...

3D ResinThis set includes one travel pod for use on all USN/USMC F-4 Phantom kitsCAD by Craig Sargent..

3D ResinThis set includes twelve (12) BDU-33 25lb practice bombs...

This set includes eight (8) wing pylons, one (1) centerline pylon, seven (7) BRU-36 ejector racks, and two (2) LAU-138 BOL launchers.3D printed and designed by Richard VanZandt using photos and measurements provided by FLD, Simon Oakes, Robert Foster and David Sweetman..

This set includes eight (8) wing pylons, one (1) centerline pylons, and seven (7) BRU-36 ejector racks.3D printed and designed by Richard VanZandt using photos and measurements provided by FLD, Simon Oakes, Robert Foster and David Sweetman..

This set includes six (6) wing pylons, two (2) centerline pylons*, seven (7) BRU-36 ejector racks and two (2) adapters used when the LAU-7 missile launcher is attached to the outboard pylons.*Different centerline pylons are configured for use with the strakes or gun pack.3D printed and designed..

This set contains two accurate fuel tanks for the AV-8B Harrier and Harrier GR.5/7/9Each tank comprises 5 parts with keys to correctly place both the fore and aft sections.Designed by Richard VanZandt of Flight Line Resin..

3D ResinThis set includes eight (8) AOA Probes. Can be used on the F/A-18A-D, AV-8B, A-6E, EA-6B and several others...

3D ResinDesigned by Richard VanZandt, this set includes one (1) pod, comprised of three parts. Main body, alignment plug, and the tail section. Assembly required after minimal cleanup of parts...

This set contains one (1) pod. The AN/ALQ-164 Defensive Electronic Countermeasures (DECM) Pod was used exclusively and frequently by the US Marine Corps AV-8B Harriers during Operation Desert Storm.While limited in its use, the pod is still carried today by the US Marine Corps and is also used by ..

3D ResinThis set contains one (1) Right Handed AN/AAQ-28 LITENING Pod in the stowed position.Used on USMC F/A-18, EA-6B, Tornado, and TyphoonVery light sanding is required to remove print support nibs from bottom of pod. Comes packaged as shown in the photo.Designed by Sandro Maljic..

3D ResinThis set contains one (1) Right Handed AN/AAQ-28 LITENING Pod in the deployed position.Used on USMC F/A-18, EA-6B, Tornado, and TyphoonVery light sanding is required to remove print support nibs from bottom of pod. Comes packaged as shown in the photo.Designed by Sandro Maljic..

3D ResinThis set contains one (1) Left Handed AN/AAQ-28 LITENING Pod in the stowed position.Used on USMC F/A-18, EA-6B, Tornado, and TyphoonVery light sanding is required to remove print support nibs from bottom of pod. Comes packaged as shown in the photo.Designed by Sandro Maljic..

3D ResinThis set contains one (1) Left Handed AN/AAQ-28 LITENING Pod in the deployed position.Used on USMC F/A-18, EA-6B, Tornado, and TyphoonVery light sanding is required to remove print support nibs from bottom of pod. Comes packaged as shown in the photo.Designed by Sandro Maljic..

The AERO-3B missile launcher was designed to be used with the AIM-9A/B/C Sidewinder missiles.This set includes 4 launchers with pylon adapters for the F-4B/N/J Phantom.Each launcher is 3D printed and require only a light sanding to remove any remnant of the support nib at the aft end of launche..

The AERO-3B missile launcher was designed to be used with the AIM-9A/B/C Sidewinder missiles.This set includes 4 launchers with pylon adapters for the F-4C/D/E Phantom.Each launcher is 3D printed and require only a light sanding to remove any remnant of the support nib at the aft end of launche..

The AERO-3B missile launcher was designed to be used with the AIM-9A/B/C Sidewinder missiles.This set includes 4 launchers with fuselage mounting adapters for the F-8E/J Crusader.Each launcher is 3D printed and require only a light sanding to remove any remnant of the support nib at the aft end..

The AERO-3B missile launcher was designed to be used with the AIM-9A/B/C Sidewinder missiles.This set includes 4 launchers and can be used on a variety of USN, USMC and USAF aircraft from the 50's and 60's.Each launcher is 3D printed and require only a light sanding to remove any remnant of the..

3D ResinThis set includes one (1) adapter and can be used on all F-4 kits. This adapter is used to carry the MER or TER on the centerline station...

3D ResinThis set includes four (4) ADU-830/A Adapters currently being used by the AV-8B II Plus to allow the carriage of AIM-120 with LAU-127 on stations 2 and/or 6, as well as AIM-9 with LAU-7 on those two stations...