Model Planes

Set includes four (4) Mk-82/BLU-111 bombs with the rough ablative coating, four (4) KMU-572 tail assemblies attached and the nose strake as separate pieces.Also included are four (4) each of the following : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

Set includes four (4) Mk-82/BLU-111 bombs with KMU-572 tail assemblies attached and the nose strake as a separate piece.Also included are four (4) each of the following : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

Set includes two (2) Thermally Protected Mk-83/BLU-110 bombs with KMU-559 guidance kit attached and the tail assemblies as separate pieces.Also included are two (2) DSU-33 proximity fuzes, two (2) MXU-735 solid nose plugs and two (2) Ogive nose plugs...

Set includes four (4) Mk-83/BLU-110 bombs with KMU-559 guidance kit attached and the tail assemblies as separate pieces.Also included are four (4) each of the following : DSU-33 proximity fuzes, MXU-735 solid nose plugs and Ogive nose plugs...

This set includes four (4) GBU-16 Thermally Protected laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fins in th..

This set includes four (4) GBU-16 laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fins in the guidance section u..

This set includes four (4) GBU-12 laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fins in the guidance section u..

The FPU-6/A Oval Fuel Tank was developed for the F/A-18A/B Hornet in 1978 and used on the FSD aircraft, as well as a few fleet Hornets into the mid 1980's. It was phased out due to fatigue anomalies caused by the oval configuration.This set includes two hollow tanks that require assembly. Some li..

Wheels designed to fit the Hasegawa F/A-18A/B/C/D Hornet Kits..

Wheels designed to fit the Kinetic F/A-18A/B/C/D Hornet Kits..

3D ResinThis set includes twenty four (24) DSU-33 Proximity Fuzes. These are designed to work with all kit supplied bombs that may not have accurate or clean versions...

3D ResinThis set includes one travel pod for use on all USN/USMC F-4 Phantom kits..

This set includes four (4) BDU-57 / 59 / 60 Laser Guided Training Rounds with separate seeker heads.Careful removal of parts from print supports and minimal clean up required.Can be used with the F-14A/B/D, F/A-18A/B/C/D/E/F and AV-8B..

3D ResinThis set includes twelve (12) BDU-33 25lb practice bombs...

This set includes eight (8) wing pylons, one (1) centerline pylon, seven (7) BRU-36 ejector racks, and two (2) LAU-138 BOL launchers.3D printed and designed by Richard VanZandt using photos and measurements provided by FLD, Simon Oakes, Robert Foster and David Sweetman..

This set includes 6 buckets that can be used to replace those found in kits that may be under detailed...

This set includes six (6) buckets that can be used in a diorama setting (ordnance loading evolution) or to replace kit parts...

3D ResinThis set contains one (1) Right Handed AN/AAQ-28 LITENING Pod in the stowed position.Used on USMC F/A-18, EA-6B, Tornado, and TyphoonVery light sanding is required to remove print support nibs from bottom of pod. Comes packaged as shown in the photo.Designed by Sandro Maljic..

3D ResinThis set contains one (1) Right Handed AN/AAQ-28 LITENING Pod in the deployed position.Used on USMC F/A-18, EA-6B, Tornado, and TyphoonVery light sanding is required to remove print support nibs from bottom of pod. Comes packaged as shown in the photo.Designed by Sandro Maljic..

3D ResinThis set contains one (1) Left Handed AN/AAQ-28 LITENING Pod in the deployed position.Used on USMC F/A-18, AV-8B and EA-6B, Tornado, and TyphoonVery light sanding is required to remove print support nibs from bottom of pod. Comes packaged as shown in the photo.Designed by Sandro Maljic..

This set includes two (2) AGM-123 Skipper anti-ship laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes for the fins in the ..

This set includes two (2) thermally protected AGM-123 Skipper anti-ship laser guided bombs. For ease of alignment, while still being easy to paint, the guidance sections and warheads are printed together.** Due to slight variations in the printers used, it may be necessary to drill out the holes ..

The AERO-3B missile launcher was designed to be used with the AIM-9B Sidewinder missile.This set includes 4 launchers with standoff adapters designed to be used on the Zoukei-Mura F-4C/D/E.Each launcher is 3D printed and come removed from the print supports. All that is needed is a light sandin..

This set contains two (2) fuel tanks with print supports attached. Use a fine tip sprue cutter to remove supports from the tank. Do not 'break' the supports free, as this can damage the surface of the tank. We have intentionally provided a photo of the tank with the supports removed in this fashion,..