Model Planes

Set contains parts for detailing of seat belts for ejection seats of the aircraft models Blackburn Buccaneer...

Set contains 3D-printed parts and colour printing for detailing of cockpit interior elements and 2 pilot seats of aircraft models Bell V-22 Osprey (HobbyBoss)."The Bell V-22 Osprey - a multi-mission, tiltrotor military aircraft with both vertical take-off and landing and short take-off and landing..

Product Type: 3D Decals Equipment Type: Seats (not included)3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - A..

Product Type: 3D Decals Equipment Type: Seats (not included)3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - A..

German WWI biplanes had an airspeed indicator that worked with an anemometer; the whole device was attached to the wing near the pilot, as can be seen in the old WWI photo on the right. With current modelling resins, in 1/48 and 1/32 scales, the narrow parts of the anemometer break easily, and the n..

Product Type: 3D Decals Equipment Type: Seats (not included)3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - A..

Set contains parts for detailing of seat belts for the helicopter models Mi-24...

Product Type: 3D Decals Equipment Type: Seats (not included)3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - A..

Set contains parts for detailing of seat belts for Martin-Baker Mk.10 seats.Use for aircraft models Aermacchi MB-339, Aermacchi S-211, AMX International AMX, Atlas Cheetah, BAE Hawk, British Aerospace Sea Harrier, CASA C-101, Chengdu JJ-5, Chengdu J-7, Guizhou JJ-7, Dassault/Dornier Alpha Jet, Das..

Set contains parts for detailing of seat belts for seats of the aircraft models Harrier GR.3, GR.7, GR.9...

Set contains parts for detailing of seat belts for ejection seats of the aircraft models Blackburn Buccaneer...

Yak 3 interior (Eduard kit)PE-resin accessories for Eduard kit..

Spitfire PRU camera setresin set for Spitfire PRU kits..

Each set includes:A full-colour cockpit set that covers the many labels found on modern cockpit side consoles and includes a full range of warning placards as found on European and US Ejector seats and hazard markings found throughout the cockpit.Includes both pre-shaped and blank hazard stripe ..

German interior set basicPE-resin basic set for Luftwaffe interiors..

Cowling fixtures and interior ribsPE accessories for scratch builders..

New to the airscale Pro range, a highly detailed set of replacement parts for the kit's rudimentary throttle, oxygen control, REVI C12/D Gunsight, Control column and an accurate seat with no moulded belts. The set is 3D printed.Experience in removing 3D parts is useful but not essential. Any support..

Upgraded high fidelity etched Nickel Silver Interior set to suit the Airfix 1/24 F6F Hellcat kit.Nickel Silver has the same properties as brass, but weathers and scratches just like the real thing.Each set includes:Fully detailed Etched Nickel Silver Instrument Panel Bulkhead, Instrument..

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..

unassembled and unpainted..

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..