Model Planes
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8099
This set is designed to fit inside the kit and force the bottom seam into the proper position and allow easy gluing and seam work...
US$17.43
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8114
3D ResinThis one piece boarding ladder is designed to fit both the Meng and Hasegawa Super Hornet / Growler kits. May also work with the Revell and Italeri kits, with possible modifications to kit needed.Designed by Richard VanZandt of Flightline Resin, item comes as shown in the photo...
US$9.75
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8079
Designed by P. Haupt, these doors provide better, and more accurate details over the kit parts.There are four (4) pieces in this set. Second aft strut door is to show antenna detail on outside surface...
US$9.75
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8078
Designed by P. Haupt, these doors provide better, and more accurate details over the kit parts.There are six (6) pieces in this set...
US$11.79
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8125
3D ResinThis is a simple tool that can be used over and over.If built as designed, the vertical tails in the Hasegawa 1/48 Hornets angle too far out. This jig helps set them at the correct angle.Simply score (do not cut off) the outside surface of the locating tabs on the tail parts where it me..
US$9.75
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8105
This set includes a total of four (4) tail stiffening plates commonly found on F/A-18A and F/A-18A+ Hornets. The four plates will complete two (2) models.3D printed, the plates have all of the rivet and screw fasteners visible. Simply remove from the support, sand the small attachment points smoot..
US$7.39
Brand: Flying Leathernecks
SKU: FLV48002
This item includes 2 sets of stiffening plates applied to the left side of each vertical tail on F/A-18A/A+ aircraft in use by the USN, USMC, Canada, Australia and Spain.Made of self adhesive vinyl, they will work with both Kinetic and Hasegawa Kits...
US$6.20
Brand: Flying Leathernecks
SKU: FL48-8106
This set includes six (6) GPS Antenna found on the F/A-18 Hornet, EA-6B Prowler, CH-46E and several other aircraft.3D printed, parts come as shown and are very easily removed from the supports using sharp sprue cutters or X-Acto type blade. Use Super Glue (CA) to attach to kit...
US$7.39
Pre-Order
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8107
3D ResinThis set includes three (3) pieces that make up the belly strap found on late F-4E and all F-4G Phantoms. Designed to be used on the Meng kits, it may work with other kits with some adjustments.The strap was also found on the F-4S and the F-4J's operated by the UK.Parts come as shown a..
US$9.75
Brand: Flying Leathernecks
SKU: FL48-8027
Designed specifically for the Tamiya F-4B, this new 3D printed fin cap allows the modeler to build F-4B's that were fitted with the AN/APR-25 antenna.Fin cap comes removed from the print supports and only needs a few swipes with a sanding stick to remove the remaining nubs. Simply glue in place an..
US$7.39
Brand: Flying Leathernecks
SKU: FL48-8025
This part is designed to be used with Bullseye Model Aviation Decal Sheet 48-017 and Furball Aero-Design Decal Sheet 48-076 when building the VF-14 and VF-32 options.Mastered by Richard VanZandt, it is a drop in replacement for kit part P18/P19...
US$7.39
Brand: Flying Leathernecks
SKU: FL48-8026
Designed specifically for the Tamiya F-4B, this new 3D printed fin cap allows the modeler to build early F-4B's, as well as USAF F-110 with little to no effort.Fin cap comes removed from the print supports and only needs a few swipes with a sanding stick to remove the remaining nubs. Simply glue i..
US$7.39
Pre-Order
Brand: Flying Leathernecks
SKU: FLV48001
Redesigned set includes the plates added to the upper wing and forward nose section. Parts adjusted to accurately fit all 1/48 F-16 kits...
US$6.20
