Model Planes

Sheet includes 4 each: .66(17mm), .58" (15mm), .54" (14mm), .50" (13mm), .41" (10mm), .33" (8mm), .25" (6mm) and .21" (5mm) when measured as squares. Comes with instructions...

Sheet of nine high-resolution Hamilton Standard prop logos. Comes with instructions. NOTE: New part number is AR49031, but number on sheet will still be AR200048 as shown...

Sheet of nine high-resolution Curtiss Electric prop logos. Comes with instructions. NOTE: New part number is AR49030, but number on sheet will still be AR100048 as shown...

105 total patches in the various sizes and shapes shown with recessed rivets...

Sheet of nine sets of prop tips and stenciled data. Comes with instructions. NOTE: New part number is AR32007, but number on sheet will still be AR300032 as shown...

Full sheet includes 39 linear inches (99 cm) of rib tape and stitches for WWI and other fabric covered aircraft...

Sheet comes with 2 each: .98" (25mm), .86" (22mm), . .80" (20mm), 74" (19mm), .61" (15mm), .49" (12mm), .37" (9mm), and .31" (8mm) swastikas when measured as squares. Comes with instructions...

Sheet comes with 4 each: .80" (20mm), 4 each .66" (17mm), 6 each .53" (13mm), 10 each .40" (10mm), and 7 each .33" (8mm) swastikas when measured as squares. Comes with instructions...

Sheet includes: Rudder Linkage Inside, Oil Cooler Access, Elevator Hinge Access, Aileron Hinge Access, No Hand Hold, Battery Vent, Battery Access, Emergency Release Inside, Jack Here, TP 100, Access, Insp., No Step, Life Raft, Relief Tube, Drain, Oil Drain, Fuel Drain, Fuel, Oil, Ground Here, Cautio..

Sheet of generic data in Grumman style font. Comes with instructions...

Sheet of generic data in Grumman style font. Comes with instructions...

Sheet of generic data in Grumman style font. Comes with instructions...

Sheet of generic data in Grumman style font. Comes with instructions...

Over 80 decals totalling over 150 square inches (381 cm) to completely rivet one kit including corrected control surfaces. Rivet decals are printed onto our exclusive Nano Film, the thinnest, strongest decal film available. Comes with illustrated colour placement booklet. Can be applied under the fi..

Over 80 decals totalling over 150 square inches (381 cm) to completely rivet one kit including corrected control surfaces. Rivet decals are printed onto our exclusive NANO FILM, the thinnest, strongest decal film available. Comes with illustrated colour placement booklet. Can be applied under the fi..

Sheet of data stencils for P-40E, but suitable for other variants. Comes with a large, full colour placement guide...

Sheet of nine high-resolution Curtiss Electric prop logos. Comes with instructions. NOTE: New part number is AR32005, but number on sheet will still be AR100032 as shown...

Water-slide Decals: Instruction: 1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them. 2. Cut out the decal you need (do it on cutting mat) 3. Grab the d..

Contains decals for 4 versionsWater-slide Decals: Instruction: 1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them. 2. Cut out the decal you need (do it ..

Decals for P-40M, Hurricane IIA, Polikarpov I-16 Rata Type 27 x 2Water-slide Decals: Instruction: 1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them. 2...

Water-slide Decals: Instruction: 1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them. 2. Cut out the decal you need (do it on cutting mat) 3. Grab the d..

Water-slide Decals: Instruction: 1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them. 2. Cut out the decal you need (do it on cutting mat) 3. Grab the d..

Type: water-slide decalsHow to apply water-slide decals:1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.2. Cut out the decal you need (do it on cutting m..

Water-slide Decals: Instruction: 1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them. 2. Cut out the decal you need (do it on cutting mat) 3. Grab the d..