Model Figures

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..

..

Set contains two pieces of machine gun Maxim in different variants. 26 resin parts and photoetched sheet...

Products made in 3D are not assembled or painted, and there may be colour differences depending on the resin.Experience in removing 3D parts is useful but not essential. Any supports connected to the detail can be cut with side cutters or a slitting disc; the remainder can be broken off with snip..

3D printed 9 parts..

3D printed 55 parts..

3D printed 46 parts..

3D printed 45 parts..

3D printed 43 parts..

It's a figure inspired by the Volunteer Soldier of the world who participated in the Ukrainian war. It's a good product to make in pairs with MF-31. MF-31 is a pose that holds standing FGM-148 Javelin's launcher. It will be a product that can decorate works and equipment set in modern times...

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..

Products made in 3D are not assembled or painted, and there may be colour differences depending on the resin.Experience in removing 3D parts is useful but not essential. Any supports connected to the detail can be cut with side cutters or a slitting disc; the remainder can be broken off with snip..

3D printed 9 parts..

3D printed 18 parts..

3D printed 9 parts..

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..

Products made in 3D are not assembled or painted, and there may be colour differences depending on the resin.Experience in removing 3D parts is useful but not essential. Any supports connected to the detail can be cut with side cutters or a slitting disc; the remainder can be broken off with snip..

Products made in 3D are not assembled or painted, and there may be colour differences depending on the resin.Experience in removing 3D parts is useful but not essential. Any supports connected to the detail can be cut with side cutters or a slitting disc; the remainder can be broken off with snip..

Products made in 3D are not assembled or painted, and there may be colour differences depending on the resin.Experience in removing 3D parts is useful but not essential. Any supports connected to the detail can be cut with side cutters or a slitting disc; the remainder can be broken off with snip..

Products made in 3D are not assembled or painted, and there may be colour differences depending on the resin.Experience in removing 3D parts is useful but not essential. Any supports connected to the detail can be cut with side cutters or a slitting disc; the remainder can be broken off with snip..

Products made in 3D are not assembled or painted, and there may be colour differences depending on the resin.Experience in removing 3D parts is useful but not essential. Any supports connected to the detail can be cut with side cutters or a slitting disc; the remainder can be broken off with snip..

3D Decals Instructions - Soak the decal in warm water for a few seconds. Once it separates from the backing paper, position it on the model. - For better adhesion, use white glue, Mr. Mark Setter, or apply the decal to a glossy surface. - Avoid leaving the decal in water for too long, as this may ca..