Menu
Your Cart

Decals for 1/72 Focke-Wulf FW-190 D-9 Part 2

Decals for 1/72 Focke-Wulf FW-190 D-9 Part 2
Decals for 1/72 Focke-Wulf FW-190 D-9 Part 2
Decals for 1/72 Focke-Wulf FW-190 D-9 Part 2
Out Of Stock
Decals for 1/72 Focke-Wulf FW-190 D-9 Part 2
Decals for 1/72 Focke-Wulf FW-190 D-9 Part 2
Decals for 1/72 Focke-Wulf FW-190 D-9 Part 2
Decals for 1/72 Focke-Wulf FW-190 D-9 Part 2
1. Fw 190D-9 (W.Nr. 211934) from the Stab of ll./JG 6. Furth Germany, 8 May 1945.
2. Fw 190D-9 from 2./JG 6. Sorau, Germany, beginning of 1945.
3. Fw 190D-9 (W.Nr. 211018) from the Stab of JG 26. Husted, Germany, January 1945.
4. Fw 190D-9 from 7./JG 26. Delmenhorst, Germany, February 1945. Pilot: Walter Stumpf.
5. Fw 190D-9 from ll./JG 54. Oldenburg, Germany, December 1944. Pilot: Werner Merz. JG 54 was the first wing to receive the Dora, in October 1944.
6. Fw 190D-9 (W.Nr.210003) from 12./JG 54. Oldenberg, Germany, October 1944.
7. Fw 190D-9 (W.Nr. 5000648 or 500641) from ll./KG (J) 27.
8. Fw 190D-9 from 7./JG 301. Stendal, Germany, April 1945. Pilot: Hagen Forster.
9. Fw 190D-9 from the Stab of ll./JG 26. Germany, January 1945. Pilot: Peter Paul Steidl.
10. Fw 190D-9 from 3./JG 301. Straubing, Germany, April 1945.
11. Fw 190D-9 from 7./JG 26. Nordhornclausheide, Germany, 14 January 1945. This plane might have been Oberleutnant Waldemar Radener's personal mount. The "Schlageter" was the only Luftwaffe wing to be entirely equipped with Doras.
12. Fw 190D-9 (W.Nr. 210239) from 6./JG 26. Flown by Uffizier Fritz Hanusch, this plane was shot down to the south of Wesel (Germany) on 9 February 1945 after a dogfight against twenty or so P-47s.

Water-slide Decals:
Instruction:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
General Info
Scale1/72
TypeModel Upgrade/Accessory
SubtypeDecals / Stickers

  • Stock: Out Of Stock
  • Reward Points: 12
  • SKU: PRS72-430
MRP: US$15.38 US$3.0319% OFF
US$12.35
(excl. Tax)
"In-Stock" Really Means It
Combine Shipping & Save

Be the first to review this product

Write a Review