1/72 Mitsubishi A6M Zero Decals
Type: water-slide decals
1. A6M2 Zero of boatswain H. Toyoshima from Hiryu aircraft carrier. The aircraft was lost on February 19, 1942
2. A6M2 Type 0 Model 21, third Kokutai No. X-108Pilot - Tamotsu Yokoyama. Takao, Formosa, 19
3. A6M2-type 0, Model 21-?Zero? IJN Carrier Akagi Pilot: PO Sueyoshi Osanai
4. A6M5-Hay Type 0 Model 52 Hay. Tsukuba Kokutai No.Tsu-46 The air base in Oita, Japan Islands Defense, February 1945
5. A6M2 Type 0 Model 21. Tainan Kokutai No. V-103 Pilot - Petty Officer Saburo Sakai, Bali, Indonesia, in February 1942
6. A6M2 Type 0 Model 21. Third Kokutai No.X-183 Pilot - Petty Officer 2nd Class Yoshiro Hashiguchi, Kendari Air Base, March 1942
7. A6M2 of P/O 1-st Cl. Simakawa Masaaki front Tainan Kokutai. End of 1941
8. A6M5-Hay Type 0 Model 52 Hay. 303rd hikotai, 203rd Kokutai No. 03-09 Pilot - Petty Officer Takeo Tanimitsu. Navy airbase Kagoshima, Japan, June 1945
9. A6M2 Type 0 Model 21. Tainan Kokutai No. V-141, 439 Pilot - Petty Officer 1st Class Yoshisuke Arita, February 1942
10. A6M2 model 11Aircraft captured army of Chiang Kai-shek.
11. A6M5 Technical Air Intelligence Center No. TAIC-8 Technical Center of Military Intelligence - Technical Air Intelligence Center (TAIC)
12. A6M2 Tainan Kokutai. V-172 No. 26, 1941 made an emergency landing in China, and was captured by Chinese nationalists.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
1. A6M2 Zero of boatswain H. Toyoshima from Hiryu aircraft carrier. The aircraft was lost on February 19, 1942
2. A6M2 Type 0 Model 21, third Kokutai No. X-108Pilot - Tamotsu Yokoyama. Takao, Formosa, 19
3. A6M2-type 0, Model 21-?Zero? IJN Carrier Akagi Pilot: PO Sueyoshi Osanai
4. A6M5-Hay Type 0 Model 52 Hay. Tsukuba Kokutai No.Tsu-46 The air base in Oita, Japan Islands Defense, February 1945
5. A6M2 Type 0 Model 21. Tainan Kokutai No. V-103 Pilot - Petty Officer Saburo Sakai, Bali, Indonesia, in February 1942
6. A6M2 Type 0 Model 21. Third Kokutai No.X-183 Pilot - Petty Officer 2nd Class Yoshiro Hashiguchi, Kendari Air Base, March 1942
7. A6M2 of P/O 1-st Cl. Simakawa Masaaki front Tainan Kokutai. End of 1941
8. A6M5-Hay Type 0 Model 52 Hay. 303rd hikotai, 203rd Kokutai No. 03-09 Pilot - Petty Officer Takeo Tanimitsu. Navy airbase Kagoshima, Japan, June 1945
9. A6M2 Type 0 Model 21. Tainan Kokutai No. V-141, 439 Pilot - Petty Officer 1st Class Yoshisuke Arita, February 1942
10. A6M2 model 11Aircraft captured army of Chiang Kai-shek.
11. A6M5 Technical Air Intelligence Center No. TAIC-8 Technical Center of Military Intelligence - Technical Air Intelligence Center (TAIC)
12. A6M2 Tainan Kokutai. V-172 No. 26, 1941 made an emergency landing in China, and was captured by Chinese nationalists.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
| General Info | |
| Scale | 1/72 |
| Type | Model Upgrade/Accessory |
| Subtype | Decals / Stickers |
- Stock: In Stock
- Reward Points: 20
- SKU: PRS72-068
- 1pcs in Stock
Print Scale Decals
MRP: US$16.41 Save: US$3.02
18% OFF
US$13.39
(excl. Tax)
"In-Stock" Really Means It
Combine Shipping & Save
SAME or Next day shipping*
There are no reviews
Maybe you can help? Many users will be grateful to you. And so are we.