1/72 Wet Decals - Aero L-39 Albatros

Type: water-slide decals

1. Aero L-39 C Albatros part: 444 minutes and PULP and PAPER PLC, NAVAL aviation number: 91 (p/n 834375) Plane of the 444-day center of combat application and re-training of pilots (BCP and PLC), naval aviation from the island of Pskov
oblast.

2. Aero L-39 C Albatros number: 41 (p/n 433021) Tambov school pilots. Airfield Michurinsky, 1990-ies.

3. Aero L-39 C Albatros number: 15 Tambov school pilots. Airfield Michurinsky, 1990-ies.

4. Aero L-39 C Albatros part: Armavirovskoe Vai, 704-th UAP number: 09 Airfield Kotelnikovo, 2003 .

5. Aero L-39 C Albatros number: 90 (c/n. 834332) pilot school of Tambov. Airfield Michurinsky, 1990.

6. Aero L-39 C Albatros Part: training air Regiment, Krasnodar higher military school of pilots (military Institute) named A.k. Serov number: 127 Presumably, 2006.

7. Aero L-39 C Albatros number: 51 air base Kirovsk.

8. Aero L-39ZA Albatros, 16 , 1st Aviation Base, Siauliai 2010.

9. Aero L-39ZA Albatros, 17 , 1st Aviation Base, Siauliai 2010.

10. Aero L-39? Albatros part: Escuela de Aviacion Militar ' Che Guevara ' number: 02 flight training organisation ' Che Guevara ', San Julian air base.

11. Aero L-39? Albatros part: 910-7th air Regiment number: 8703 the Academy AIR FORCE Vietnam, Nha Trang air base.

12. Aero L-39? Albatros part: Fighter Squadron, Royal Air Force Cambodia number: 25 (132135) Pochentong Airbase.

13. Aero L-39 C Albatros Part: not available number: 11 one of Chechen ' Albatross ', destroyed at Khankala December 1, 1994. Chechen AIR FORCE markings in the form of 'Republic of Ichkeria '.

14. Aero L-39 C Of the Ghana AIR FORCE: number: G-901.

15. Aero L-39ZO part: FAG-25 number: 144 All East German L-39ZO served at JAG/FAG-25. This aircraft after the unification of Germany got the number 28 06. However, he did not have the black cross and was never used. Today it is a Museum in Berlin.

16. Aero L-39ZO part: LyAAF number: 3547.

How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softener is also recommended at this stage. After applying softener, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.