1/72 Wet Decals - Dassault/Dornier Alpha Jet Part 1
Type: water-slide decals
1. Alpha Jet MS.1 Serial: 350 The Alpha Jet is in the Egypt Air Force : the 'standard' trainer (MS.1)
2. Alpha Jet Unit: unknown. Serial: 231 Alpha Jet No 231 in the colours of the Moroccan Air Force, which has ordered 24 of these basic trainers.
3. Alpha Jet Unit: NAF Serial: NAF-452. The NAT deployed only two Alpha Jets in support of the Nigerian ECOMOG contingent in Sierra Leone. It remains unknown if the same two examples remained in country between their first deployment, in 1995, and 1999. Western specialized media claimed that an NAF Alpha Jet was shot down by anti-aircraft fire of the fighters belonging to Sierra Leonean junta, on 8 February 1998, but Grp.Cpt. Sat Easterbook from ECOMOG categorically denied such a claim, in early 1999.
4. Alpha Jet B Unit: BAF. Serial: AT-29.
5. Alpha Jet. An export Alpha Jet as supplied to Qatar.
6. Alpha Jet Serial: 5U-MBA. An export model Alpha Jet in the colours and markings of the Togo Air Force, which has ordered six.
7. Alpha Jet Unit: Esquadra 301 'Jaguares', Forca Aerea Portuguesa. Serial: 15202. Base Aerea No.11, Beja, 2002.
8. Alpha Jet A Unit: 231 Sqn, 23rd Wing, RTAF. Serial: 23142. RTAFB Udon Thani, circa 2004.
9. Alpha Jet Unit: Escadrille de Chasse, FACI. Serial: TU-VCA (CA-1) FACI received six Alpha Jets in October 1980.
10. Alpha Jet A Unit: Waffenschule 50/Furstenfeldbruck (in crisis time JaboG49) Serial: 40+17 Based at Furstenfeldbruck. The aircraft carry ventral gun pack.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softener is also recommended at this stage. After applying softener, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
1. Alpha Jet MS.1 Serial: 350 The Alpha Jet is in the Egypt Air Force : the 'standard' trainer (MS.1)
2. Alpha Jet Unit: unknown. Serial: 231 Alpha Jet No 231 in the colours of the Moroccan Air Force, which has ordered 24 of these basic trainers.
3. Alpha Jet Unit: NAF Serial: NAF-452. The NAT deployed only two Alpha Jets in support of the Nigerian ECOMOG contingent in Sierra Leone. It remains unknown if the same two examples remained in country between their first deployment, in 1995, and 1999. Western specialized media claimed that an NAF Alpha Jet was shot down by anti-aircraft fire of the fighters belonging to Sierra Leonean junta, on 8 February 1998, but Grp.Cpt. Sat Easterbook from ECOMOG categorically denied such a claim, in early 1999.
4. Alpha Jet B Unit: BAF. Serial: AT-29.
5. Alpha Jet. An export Alpha Jet as supplied to Qatar.
6. Alpha Jet Serial: 5U-MBA. An export model Alpha Jet in the colours and markings of the Togo Air Force, which has ordered six.
7. Alpha Jet Unit: Esquadra 301 'Jaguares', Forca Aerea Portuguesa. Serial: 15202. Base Aerea No.11, Beja, 2002.
8. Alpha Jet A Unit: 231 Sqn, 23rd Wing, RTAF. Serial: 23142. RTAFB Udon Thani, circa 2004.
9. Alpha Jet Unit: Escadrille de Chasse, FACI. Serial: TU-VCA (CA-1) FACI received six Alpha Jets in October 1980.
10. Alpha Jet A Unit: Waffenschule 50/Furstenfeldbruck (in crisis time JaboG49) Serial: 40+17 Based at Furstenfeldbruck. The aircraft carry ventral gun pack.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softener is also recommended at this stage. After applying softener, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
| General Info | |
| Scale | 1/72 |
| Type | Model Upgrade/Accessory |
| Subtype | Decals / Stickers |
- Stock: In Stock
- Reward Points: 20
- SKU: PRS72-182
- 1pcs in Stock
Print Scale Decals
MRP: US$17.09 Save: US$3.08
18% OFF
US$14.01
(excl. Tax)
"In-Stock" Really Means It
Combine Shipping & Save
SAME or Next day shipping*
There are no reviews
Maybe you can help? Many users will be grateful to you. And so are we.