Model Planes

..

The plastic kit gear causes the model to sit too high. This set corrects this problem...

The set contains 65 parts and wire. Valves in open or closed position...

..

**NOTE:Slight warpage might occurred to the malleable nature of white metal and is easily straightened. A brief but succinct tutorial for working with white metal can be found on the homepage the their official website: www.scaleaircraftconversions.com..

**NOTE:Slight warpage might occurred to the malleable nature of white metal and is easily straightened. A brief but succinct tutorial for working with white metal can be found on the homepage the their official website: www.scaleaircraftconversions.com..

Important note: Study the photo carefully. This set contains the primary main gear parts with some of the retraction arm parts and additional plumbing. Some ancillary parts will need to be fashioned by the modeler. No nose gear is provided. Also, the SAC set is not a duplicate of the plastic gear an..

This is a plastic model kit, which comes unassembled and unpainted. So glue, model paints and other basic modelling tools are additionally required...

Paint Mask:Preparing the masks: Masks should not be stretched during the application process as they are flexible and this could cause deformation. Remove the whole mask if necessary, and then apply again. Once placed on the model, the mask surface should be adjusted to the surface of the model ..

Paint masks for "NASA" "USAF" "U.S. AIR FORCE" stars'n'bars and serial numbers. Masks are manufactured by Miracle Masks. This is a newly updated version of the msks set which now includes the early style "NASA" rudder logo design as used on early XLR-11 powered X-15's...

The is a strike camera chin pod for the nose of the Zoukei Mura F-4C. This pod was used for example by Col Robin Olds on Operation Bolo. Later, many of these chin pods were re-fitted with forward RHAW pods, retaining only the rearward facing camera. Included in this set are two types of front ends -..

This is a non-IRST chin (radome) pod for early F-4B's, specifically for the Tamiya kit. This pod/fairing was fitted to early F-4B's before and after the short "era" of the IRST system. While in development during the F4H /F4H-1 phase, the first regular F-4B off the production line were not yet fitte..

Stabilator for all types of F-4 Phantom that used the unslotted stab. For both the Hasegawa and Academy kits. Includes separate PE pivot cover plates and stiffener "fishplates" (for Air Force variants). The stabs can be used as a drop fit replacement for the kit parts or, with some work on the kit p..

This is a set of aft fuselage half parts that correct the shape error on the engine shoulders of the Zoukei Mura short nose Phantoms. in addition to the re-shaped geometry, some surface detail has been improved. Please note that this is not a drop-fit replacement set. Cutting of the fuselage is requ..

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

Hollowed, thin-walled resin part to detail the open-ended Jet Fuel Starter (JFS) exhaust tubing as found on modern Eagles, such as the F-15C and F-15E Strike Eagle. A small part that adds detail and interest to this area and brings it up to date on all 1:48 F-15 kits...

This is a full conversion set to build an NF-104A aerospace/astronaut trainer aircraft from the Kinetic F-104G kit. The set comes with all parts needed, some injection moulded plastic, some 3D printed, plus a turned brass pitot boom and a full set of decals by Caracal (printed by Cartograf)...

This is a replacement resin fin tip for the HobbyBoss Intruder family. The HB fin tip has the wrong shape and once you have noticed the error you can't ignore it any longer...the surface detail is slightly corrected and enhanced as well. The required cut on the kit is fairly simple as it's along a p..

This is a cockpit set for Kitty Hawk's FJ-3 Fury kit (1:48). It includes a corrected and detailed seat with parachute and harness in place (which differs from the FJ-2 seat in several details), a detailed rear cockpit bulkhead and turtle deck, the FJ-3 specific antenna assembly (3D printed part) as ..

This is a replacement nose landing gear strut for Kitty Hawk's FJ-2 and FJ-3 Fury kits. It is 3D printed in one piece in strong resin and corrects the misshapen kit part. A lot of detail has been added and refined and as such the item is both a significant upgrade over the kit part as well as an evo..

This is a set of corrected engine nacelles with intakes, exhausts and pylons for the Trumpeter A-3 Skywarrior kits in 1:48. Suitable for all variants. This set also includes parts that enable the modeller to build the kit with dropped flaps. Please note that the first print run of the instructions m..

This is an update set for ClearProp's D-21 kit. It contains more detailed and more accurate engine sets (with one-piece nozzle), intake with one-piece spike, new back plate and better proportioned pitot and a camera to go behind the glass...

This is a resin Canberra PR.9 and B(I)8 canopy in 1:48 scale with the correct circular cross section that replaces the Airfix canopy which has an incorrect "U" cross section. As the correct cross section is circular, the offset position makes it "tuck under" on the left side and that is not represen..