Model Planes

AN/ALQ-144, ready to paint and attach to your model.For AH-1W, AH-64A/D/E, UH-1N, H-60, OH-58, VH-3D and OV-10..

3D ResinThis set contains one (1) Left Handed AN/AAQ-28 LITENING Pod in the stowed position.Used on USMC F/A-18, EA-6B, Tornado, and TyphoonVery light sanding is required to remove print support nibs from bottom of pod. Comes packaged as shown in the photo.Designed by Sandro Maljic..

This set includes fifteen (15) total air temperature probes used on a variety of aircraft.Designed by Craig Sargent..

Vinyl Mask..

Waterslide Decals printed by Microscale (Insert printed by Cartograf). 5.5 x 8.5 inch sheet..

The AERO-3B missile launcher was designed to be used with the AIM-9B Sidewinder missile.This set includes 4 launchers with standoff adapters designed to be used on the Tamiya F-4B.Each launcher is 3D printed and come removed from the print supports. All that is needed is a light sanding to remo..

The AERO-3B missile launcher was designed to be used with the AIM-9B Sidewinder missile.This set includes 4 launchers with standoff adapters designed to be used on the Hasegawa F-8E/J for direct fuselage mounting.Each launcher is 3D printed and come removed from the print supports. All that is ..

The AERO-3B missile launcher was designed to be used with the AIM-9B Sidewinder missile.This set includes 4 launchers and can be used on a variety of USN, USMC and USAF aircraft from the 50's and 60's.Each launcher is 3D printed and are easily removed from the print supports by using a sprue cu..

3D ResinThis set includes two (2) AERO-1D 300 gallon fuel tanks with the three fin tail. Each tank is made up of four parts. Some light sanding will be needed to remove the small nibs from the print supports.Like most of our items, parts are removed from the print supports prior to curing and pack..

3D ResinThis set includes two (2) AERO-1D 300 gallon fuel tanks with the single fin tail. Each tank is made up of four parts. Some light sanding will be needed to remove the small nibs from the print supports.Like most of our items, parts are removed from the print supports prior to curing and pa..

3D ResinThis set includes two (2) AERO-1D 300 gallon fuel tanks with the two fin tail. Each tank is made up of four parts. Some light sanding will be needed to remove the small nibs from the print supports.Like most of our items, parts are removed from the print supports prior to curing and packag..

3D ResinThis set includes two (2) AERO-1D 300 gallon fuel tanks with the bobtail. Each tank is made up of four parts. Some light sanding will be needed to remove the small nibs from the print supports.Like most of our items, parts are removed from the print supports prior to curing and packaging a..

3D ResinThis set includes four (4) ADU-830/A Adapters currently being used by the AV-8B II Plus to allow the carriage of AIM-120 with LAU-127 on stations 2 and/or 6, as well as AIM-9 with LAU-7 on those two stations...

3D ResinThis set includes four (4) ADU-299 Adapters. These are used to allow aircraft to carry the LAU-7 missile launcher on stations not normally designed to carry that launcher...

This set includes three (3) ADM-141 TALD.The TALD was used with great success on SEAD missions in the opening stages of Operation Desert Storm in 1991. More than 100 were launched on the opening night of the war. This prompted the Iraqi air defense to activate many of its radars most of which wer..

Simple to use pre-cut vinyl canopy and wheel mask for the Hobbyboss TA-7C and A-7K kits...

Canopy, wheel mask for Hobbyboss kits..

Set FL48-8015 contains four correct SUU-63C/A wing pylons and one correct SUU-62C/A centerline pylon for the F/A-18A++, C and D.Each set also includes five (5) unlocked BRU-32's and five (5) locked BRU-32's to more accurately depict the different configurations with or without ordnance loaded.T..

Vinyl Mask..

Vinyl Mask..

Vinyl Mask..

Vinyl Mask..

3D ResinThis set includes two (2) XM158A1 Rocket Launchers.The Launcher was a seven-tube, reloadable, reusable, repairable 2.75" rocket launcher M158A1 was a variant of the M158 that included a modified hardback mount..

3D ResinThis is a two piece 3D printed set of the SATCOM antenna mounted to the top of the main rotor mast on the UH-1Y Helicopter.Simply glue the antenna to the top center of the base, paint and attach to your model. Parts come ready to install with no clean up required...