Print Scale 48-061 1/48 Bell OH-58 Kiowa Helicopter (Part 2) Decals
Out Of Stock
Type: water-slide decals
1. OH-58D "Monsta" 95-00004 (50004) C-Troop, 3/17th Cavalry Regiment, Iraq 2004.
2. This OH-58D (R) was assigned to E Troop, 1st Squadron, 7th Cavalry Regiment 1st Cavalry Division, in Bosnia in1998 as part of SFOR. A 1st Cavalry emblem is on the nose of the Warrior. The ?Bounty Hunter? emblem of E Troop is on the right side of the ALQ-144 pedestal, and the ?Garryowen? crest is on the left.
3. OH-58A 70-15236 (15236) Australian Army, 161 Recce Flight Assoc, Nui Dat, Vietnam 1971.
4. Bell 206B A17-003 Australian Army, Brisbane, Australia 1971.
5. Bell 206B A17-043 Australian Army, Australia 2002.
6. CH-136 136213 early training scheme, Canada 1971.
7. CH-136 136207 3CFFTS (training squadron), Canada 1980.
8. OH-58A 3C-OH Austria 2010.
9. Hkp-6B 06047 Sweden Navy, Berga, Sweden 1980.
10. Bell 206 131 Light Helicopter Squadron, Israel 1998.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
1. OH-58D "Monsta" 95-00004 (50004) C-Troop, 3/17th Cavalry Regiment, Iraq 2004.
2. This OH-58D (R) was assigned to E Troop, 1st Squadron, 7th Cavalry Regiment 1st Cavalry Division, in Bosnia in1998 as part of SFOR. A 1st Cavalry emblem is on the nose of the Warrior. The ?Bounty Hunter? emblem of E Troop is on the right side of the ALQ-144 pedestal, and the ?Garryowen? crest is on the left.
3. OH-58A 70-15236 (15236) Australian Army, 161 Recce Flight Assoc, Nui Dat, Vietnam 1971.
4. Bell 206B A17-003 Australian Army, Brisbane, Australia 1971.
5. Bell 206B A17-043 Australian Army, Australia 2002.
6. CH-136 136213 early training scheme, Canada 1971.
7. CH-136 136207 3CFFTS (training squadron), Canada 1980.
8. OH-58A 3C-OH Austria 2010.
9. Hkp-6B 06047 Sweden Navy, Berga, Sweden 1980.
10. Bell 206 131 Light Helicopter Squadron, Israel 1998.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
| General Info | |
| Scale | 1/48 |
| Type | Model Upgrade/Accessory |
| Subtype | Decals / Stickers |
| Minimum Age | 14 Years |
- Stock: Out Of Stock
- Reward Points: 10
- SKU: PRS48-061
Print Scale
MRP: US$10.91 Save: US$2.92
26% OFF
US$7.99
(incl. Tax)
"In-Stock" Really Means It
Combine Shipping & Save
SAME or Next day shipping*
There are no reviews
Maybe you can help? Many users will be grateful to you. And so are we.