Echelon Fine Details P353001 Decals for 1/35 US Army & USMC Patches, Insignias and Ranks
Discontinued
Water-slide Decals
Suitable for 1/35 figures of Operation Enduring Freedom (Afghanistan) and Operation Iraqi Freedom theater of operations, and Vietnam war was well, these are screen printed by Microscale.
Special feature: unique helmet patches for the 101st airborne! Just the "Screaming Eagles" patch for the arm would not be enough. Also, different kinds of Ranger shoulder tabs.
The name patches already come with names, but modellers can make their own name patches if they like - you'll need a sharp blade, a good set of tweezers and also a good pair of eyes!
Primary Insignias include:
1st Infantry Division
2nd Infantry Division
3rd Infantry Division
4th Infantry Division
24th Infantry Division
82nd Airborne Division
101st Airborne Division
5th Special Forces Group Airborne
3rd Army
10th Mountain Division
1st Cavalry
1st Armoured Division
South Dakota National Guard
220th Military Police Brigade
US Army Military Assistant Command
Elements Central Command
Each of the insignias and patches are carefully created in 1/35 to match closely to the dimensions of the actual patches. No effort is spare from creating each artwork - if you can't see the details on the sheet, it means it's too fine to be printed in 1/35! Hopefully, they will make it in 1/16th scale
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
Suitable for 1/35 figures of Operation Enduring Freedom (Afghanistan) and Operation Iraqi Freedom theater of operations, and Vietnam war was well, these are screen printed by Microscale.
Special feature: unique helmet patches for the 101st airborne! Just the "Screaming Eagles" patch for the arm would not be enough. Also, different kinds of Ranger shoulder tabs.
The name patches already come with names, but modellers can make their own name patches if they like - you'll need a sharp blade, a good set of tweezers and also a good pair of eyes!
Primary Insignias include:
1st Infantry Division
2nd Infantry Division
3rd Infantry Division
4th Infantry Division
24th Infantry Division
82nd Airborne Division
101st Airborne Division
5th Special Forces Group Airborne
3rd Army
10th Mountain Division
1st Cavalry
1st Armoured Division
South Dakota National Guard
220th Military Police Brigade
US Army Military Assistant Command
Elements Central Command
Each of the insignias and patches are carefully created in 1/35 to match closely to the dimensions of the actual patches. No effort is spare from creating each artwork - if you can't see the details on the sheet, it means it's too fine to be printed in 1/35! Hopefully, they will make it in 1/16th scale
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
| General Info | |
| Scale | 1/35 |
| Type | Model Upgrade/Accessory |
| Subtype | Decals / Stickers |
| Minimum Age | 14 Years |
- Stock: Out Of Stock
- Reward Points: 13
- SKU: EC P353001
Echelon Fine Details
This item is currently unavailable
It has been discontinued or is indefinitely out of stock. Unfortunately, we are uncertain if or when it will be available again. For further information or assistance in finding equivalent products, please feel free to submit an enquiry.
"In-Stock" Really Means It
Combine Shipping & Save
SAME or Next day shipping*
There are no reviews
Maybe you can help? Many users will be grateful to you. And so are we.