Flying Leathernecks
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8079
Designed by P. Haupt, these doors provide better, and more accurate details over the kit parts.There are four (4) pieces in this set. Second aft strut door is to show antenna detail on outside surface...
US$9.75
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8134
3D ResinThis set includes the following items :Updated and Detailed Instrument Panel for BuNo's 163985 and Up
Correct and Detailed WSO Instrument Panel for BuNo's 163986 and Up
Correct WSO Instrument Panel Cover for the F/A-18D
Left and Right side console WSO Control Sticks
Rudder Pedals x 2
GPS A..
US$17.43
Pre-Order
Brand: Flying Leathernecks
SKU: FL48023
Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..
US$23.02
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8133
3D ResinThis set includes the following items :Updated and Detailed Instrument Panel for BuNo's 163985 and Up
Rudder Pedals
GPS Antenna
Shark Fin UHF/VHF Antenna
Standard Comm Antenna
AN/APX-111 IFF Antenna
JHMCS Sensor
AOA Probes..
US$11.79
Brand: Flying Leathernecks
SKU: FLM48-9
This set includes a holographic vinyl piece for the FLIR pod window and a small decal sheet with stencil data markings for the kits LAU-7 missile launchers.The decal is screen printed by Microscale...
US$6.20
Pre-Order
Brand: Flying Leathernecks
SKU: FL48009
Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..
US$23.02
Pre-Order
Brand: Flying Leathernecks
SKU: FL48008
Waterslide Decals printed by Microscale (Insert printed by Cartograf). 8.5 x 11.0 inch sheet..
US$23.02
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8078
Designed by P. Haupt, these doors provide better, and more accurate details over the kit parts.There are six (6) pieces in this set...
US$11.79
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8071
Wheels designed to fit the Hasegawa F/A-18A/B/C/D Hornet Kits..
US$9.75
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8125
3D ResinThis is a simple tool that can be used over and over.If built as designed, the vertical tails in the Hasegawa 1/48 Hornets angle too far out. This jig helps set them at the correct angle.Simply score (do not cut off) the outside surface of the locating tabs on the tail parts where it me..
US$9.75
Brand: Flying Leathernecks
SKU: FLS48001
This set includes a total of six (6) HUD's for the F/A-18A/B/C/D Hornet cut in .005 clear styrene. They are direct replacements for the overly thick kit pieces. Simply cut from runner and attach in place of kit item. Recommend use with a photo-etch HUD frame...
US$6.20
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8056
This set includes correctly shaped and sized LEX Fence parts applicable to all 1/48 F/A-18A/B/C/D Hornet kits...
US$7.39
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8000
All NEW design HUD assembly for use with the Hasegawa or Kinetic kits. Complete unit is 3D printed and comes ready to install after a small modification to the kit parts.Includes die cut 'glass' in .005 clear styrene..
US$7.39
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8105
This set includes a total of four (4) tail stiffening plates commonly found on F/A-18A and F/A-18A+ Hornets. The four plates will complete two (2) models.3D printed, the plates have all of the rivet and screw fasteners visible. Simply remove from the support, sand the small attachment points smoot..
US$7.39
Pre-Order
Brand: Flying Leathernecks
SKU: FL48-8010
All NEW design HUD assembly for use with the Hasegawa or Kinetic kits. Complete unit is 3D printed and comes ready to install after a small modification to the kit parts.Includes die cut 'glass' in .005 clear styrene..
US$7.39
Brand: Flying Leathernecks
SKU: FLV48002
This item includes 2 sets of stiffening plates applied to the left side of each vertical tail on F/A-18A/A+ aircraft in use by the USN, USMC, Canada, Australia and Spain.Made of self adhesive vinyl, they will work with both Kinetic and Hasegawa Kits...
US$6.20
Brand: Flying Leathernecks
SKU: FL48-8106
This set includes six (6) GPS Antenna found on the F/A-18 Hornet, EA-6B Prowler, CH-46E and several other aircraft.3D printed, parts come as shown and are very easily removed from the supports using sharp sprue cutters or X-Acto type blade. Use Super Glue (CA) to attach to kit...
US$7.39
Pre-Order
