Echelon Fine Details D356037 1/35 Paint Mask - LSSAH Panzer.IV Ausf.G Kharkov Numbers (Set B)
Discontinued
Paint Mask: Semi-transparent masking material
The answer for Kharkov LSSAH Panzer IV Ausf. Gs that you've always wanted to build. With masks, you can better decide for yourself what base colour(s) the 1.SS tanks ought to be: Panzer Grey; Dark Yellow; Dark Yellow with Dark Green camouflage; or even RED (if you still insist on this)!
Set B comes with a mix of 3 vehicles: 215; 228; and 615. It also comes with a duplicate just in case the first piece is messed up! Masks for balkankreuz are provided and also the generic "blank out" for the "Dietrich". Due to the complexity of the 1.SS marking and the limitations of the mask cutter, the actual "Dietrich" emblem is NOT provided. Therefore, you have to source out your own "Dietrich" emblems, either from Dragon's Kharkov Ausf G kit (or other kits), or from AXT351016.
This set can be used in conjunction with AXT351016. If you're after the cleaner "getting ready for epic battle" look when the temporary white wash have been freshly applied, then this set alone is sufficient for that purpose. However, if you prefer an extremely worn-out look on your Ausf Gs such as the excess fading of temporary white wash with the permanent white-outlined turret numbers fully exposed, then AXT351016 is highly recommended to go with this set!
About the material: the low-tack mask material is almost transparent so you can see better of the surface area where each mask goes over. Due to the transparency of the material, the masks can be rather hard to see on the backing sheet. Therefore the edges of each mask is coloured so you find each mask easily.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
The answer for Kharkov LSSAH Panzer IV Ausf. Gs that you've always wanted to build. With masks, you can better decide for yourself what base colour(s) the 1.SS tanks ought to be: Panzer Grey; Dark Yellow; Dark Yellow with Dark Green camouflage; or even RED (if you still insist on this)!
Set B comes with a mix of 3 vehicles: 215; 228; and 615. It also comes with a duplicate just in case the first piece is messed up! Masks for balkankreuz are provided and also the generic "blank out" for the "Dietrich". Due to the complexity of the 1.SS marking and the limitations of the mask cutter, the actual "Dietrich" emblem is NOT provided. Therefore, you have to source out your own "Dietrich" emblems, either from Dragon's Kharkov Ausf G kit (or other kits), or from AXT351016.
This set can be used in conjunction with AXT351016. If you're after the cleaner "getting ready for epic battle" look when the temporary white wash have been freshly applied, then this set alone is sufficient for that purpose. However, if you prefer an extremely worn-out look on your Ausf Gs such as the excess fading of temporary white wash with the permanent white-outlined turret numbers fully exposed, then AXT351016 is highly recommended to go with this set!
About the material: the low-tack mask material is almost transparent so you can see better of the surface area where each mask goes over. Due to the transparency of the material, the masks can be rather hard to see on the backing sheet. Therefore the edges of each mask is coloured so you find each mask easily.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
| General Info | |
| Scale | 1/35 |
| Type | Model Upgrade/Accessory |
| Subtype | Decals / Stickers |
| Minimum Age | 14 Years |
- Stock: Out Of Stock
- Reward Points: 6
- SKU: EC D356037
Echelon Fine Details
This item is currently unavailable
It has been discontinued or is indefinitely out of stock. Unfortunately, we are uncertain if or when it will be available again. For further information or assistance in finding equivalent products, please feel free to submit an enquiry.
"In-Stock" Really Means It
Combine Shipping & Save
SAME or Next day shipping*
There are no reviews
Maybe you can help? Many users will be grateful to you. And so are we.