Hypersonic Models

This is a full-length resin exhaust and nozzle set with the specific detail for EA-6B Prowlers which have an upgraded engine and different nozzle to the A-6 Intruder family. The instructions are based on fitting it to the Kinetic/Italeri kits, but the modeller may be able to adapt them to the Revell..

Paint masks for "NASA" "USAF" "U.S. AIR FORCE" stars'n'bars and serial numbers. Masks are manufactured by Miracle Masks. This is a newly updated version of the msks set which now includes the early style "NASA" rudder logo design as used on early XLR-11 powered X-15's...

The is a strike camera chin pod for the nose of the Zoukei Mura F-4C. This pod was used for example by Col Robin Olds on Operation Bolo. Later, many of these chin pods were re-fitted with forward RHAW pods, retaining only the rearward facing camera. Included in this set are two types of front ends -..

This is a non-IRST chin (radome) pod for early F-4B's, specifically for the Tamiya kit. This pod/fairing was fitted to early F-4B's before and after the short "era" of the IRST system. While in development during the F4H /F4H-1 phase, the first regular F-4B off the production line were not yet fitte..

Stabilator for all types of F-4 Phantom that used the unslotted stab. For both the Hasegawa and Academy kits. Includes separate PE pivot cover plates and stiffener "fishplates" (for Air Force variants). The stabs can be used as a drop fit replacement for the kit parts or, with some work on the kit p..

Stabilator for all types of F-4 Phantom that use the slotted stab. For both the Hasegawa and Academy kits. Includes separate PE pivot cover plates and stiffener "fishplates" (for Air Force variants). The stabs can be used as a drop fit replacement for the kit parts or, with some work on the kit plas..

F-4 Phantom outer pylons, Air Force type, 1:48, designed for the Zoukei Mura line of kits. The pylons have the correct outboard angle built in and come with separate sway brace pins so stores can be mounted at correct angles, either canted in line with the pylon or perpendicular to the ground...

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

Hollowed, thin-walled resin part to detail the open-ended Jet Fuel Starter (JFS) exhaust tubing as found on modern Eagles, such as the F-15C and F-15E Strike Eagle. A small part that adds detail and interest to this area and brings it up to date on all 1:48 F-15 kits...

This is a set of two SR-1 seats for the new Revell 1:48 SR-71. The seats are very accurate in dimension and detail and have been fully CAD designed. The two seats in the set are not identical in the draping/positioning of the belts and hoses. One modification to a detail on the seat was made to adap..

This is a conversion set for building an F-104B or early F-104D with downward firing C-1 ejection seats. As a base kit a Kinetic F-104D or TF-104G is needed. This conversion contains three new clear canopy parts (machine cast from transparent, UV stable resin), two C-1 seats plus ejection rails, a n..

This is a backdate set for Kinetic's F-104A/C kit to build an early F-104A with the downward firing C-1 ejection seat. The set includes parts from the F-104A Late set (lower fuselage insert, alternate hot air exhaust panel, L-brackets) plus the C-1 seat, ejection rails, rear cockpit bulkhead, forwar..

This is an extensive and complete conversion set to build JF-104A #961, the reaction control systems training aircraft, from the Kinetic F-104A/C Starfighter kit.The set contains:- wing tip pods and nose cone with RCS thrusters, a brass pitot boom (made by Master) with printed vanes all required..

This is a replacement resin fin tip for the HobbyBoss Intruder family. The HB fin tip has the wrong shape and once you have noticed the error you can't ignore it any longer...the surface detail is slightly corrected and enhanced as well. The required cut on the kit is fairly simple as it's along a p..

This is a backdate set for the (new tool) Kinetic F-16A kit and contains parts to build Block 1,5 and 10 aircraft. The set includes small stabilators with thin static wicks, early instrument panel and coaming, Environment Control System (ECS) exhaust panel, RWR and rectancular UHF antennas. The stab..

This is a corrected nose intake part for the Kitty Hawk FJ-3 Fury kit. It is a drop-in replacement for the kit part and features a corrected nose profile, in particular around the upper lip where the small radome is located. The kit part is too blunt, in the same way as the FJ-2 part is. The panel l..

This is a cockpit set for Kitty Hawk's FJ-3 Fury kit (1:48). It includes a corrected and detailed seat with parachute and harness in place (which differs from the FJ-2 seat in several details), a detailed rear cockpit bulkhead and turtle deck, the FJ-3 specific antenna assembly (3D printed part) as ..

This is a replacement nose landing gear strut for Kitty Hawk's FJ-2 and FJ-3 Fury kits. It is 3D printed in one piece in strong resin and corrects the misshapen kit part. A lot of detail has been added and refined and as such the item is both a significant upgrade over the kit part as well as an evo..

This is a replacement nose landing gear strut for Kitty Hawk's FJ-2 and FJ-3 Fury kits. It is 3D printed in one piece in strong resin and corrects the misshapen kit part. A lot of detail has been added and refined and as such the item is both a significant upgrade over the kit part as well as an evo..

This is a set of small stabilators for Kinetic's F-16A and B models. The parts are the same as found in my F-16A Backdate Set (Block 1-10),so the stabilators themselves (cast in strong resin) plus the printed static dischargers. (No other parts are included)This set is very handy for example wit..

This is a drag chute compartment with dropped chute canister for any Kinetic F-104 Starfighter kits.Supplied will be both the empty, lowered canister with dropped retainer flap (for post-landing) as well as a canister stuffed with a packed chute and rased retainer flap...

A set of two Martin Baker Mk. H5 ejection seats for early F-4B, F-4C and F-4D Phantoms (until around 1970). Suitable for and tested with Academy, Hasegawa and Zoukei Mura kits. The seats have cast on seat belts which differ from each other...

This is an update set for ClearProp's D-21 kit. It contains more detailed and more accurate engine sets (with one-piece nozzle), intake with one-piece spike, new back plate and better proportioned pitot and a camera to go behind the glass...