CMK

A trio of standing figures, two officers and a mechanic of the Imperial German Air Service. One of the officers bears striking resemblance to Hermann Goering and wears his flying suit, the second of the officers is in the uniform and the mechanic is portrayed in workwear. Operators: Germany/WWI..

Germany entered the war with two versions of G7 torpedoes of standard calibre of 53.3cm. The G7a version was steam-powered and therefore the torpedo was leaving a trace on the water surface and was also noisy. However, it was significantly faster than the electric powered G7e version. The G7a was us..

The same pair of soldiers as in the 1/48 set, now scaled down to 1/72 and 3D printed. A pair of German soldiers with military type bicycles and armament. One soldier rides his bike, the other one pushes it besides him. The armament carried on the bikes is quite varied, from a rifle to a pair of panz..

(Type: model figures) This is a resin model kit, which comes unassembled and unpainted. So glue, model paints and other basic modelling tools are additionally required...

U-Boot IX Weapon Conversion set for REV detail set..

The Revell's 1/72 U-boot typ IX model features the bow and stern torpedo tubes closed. However, before the torpedoes were launched, the tubes were flooded with water and open. And this set offers detailed resin cast bow and stern torpedo tubes with their muzzle door open. 3D-designed, master pattern..

These three WW II German submarine sailor figures were prepared to accompany the new Revell U-boot Typ IX. The standing sailors are unshaved due to the long voyage. One of the sailors walks down the deck, the other two stand still. Except of the separately cast heads, all figures are cast in one pie..

(Type: model figures) This is a resin model kit, which comes unassembled and unpainted. So glue, model paints and other basic modelling tools are additionally required. Couple of interior sets have been prepared for the new Revell U-boot IXC and one of these detailed sets is the Command Section N720..

Another of our interior sets for the new Revell U-boot IXC model is the Front Torpedo Section, set no. N72011. This set could be filled with figurines of three German submarine sailors handling a torpedo. One sailor is kneeling in front of the torpedo, the other two are handling the torpedo while st..

3D-printed figures of the searchlight crew. One of the soldiers is portrayed sitting (resin cast one piece with his seat) operating the searchlight (the figure is one piece with a seat) while the other, a non-commissioned officer, is standing watching the target through his binoculars. The figures..

..

This is a resin model kit, which comes unassembled and unpainted. So glue, model paints and other basic modelling tools are additionally required.Germany, France, Netherlands..

Nicely detailed figure of an RAF pilot as sitting in the cockpit plus two figures of his ground crew while preparing the fighter plane for take off from an African desert air strip. The set has been tailored to fit the new Special Hobby P-40 kit, or to be more precise the Kittyhawk as the plane was ..

The new PT-109 model will certainly benefit from the addition of this set which offers substantially higher levels of detail comparing to the original styrene items...

..

For the new Special Hobby P-40N kits (later blocks), but not just for these kits, has been designed this set which brings the modeller a new cast pilot's seat with belts. 3D designed, the seat master pattern was produced using a 3D printer...

The later blocks of the P-40N fighters from Special Hobby, but also any other kit of this version will no doubt enhance their look by the addition of this new seat. No seat belts, 3D designed, master parts produced using a 3D printer...

This seat is intended to be used with the new Special Hobby P-40 kits of the E, K, M and N-1 verisons or the earlier released P-40 F,L kits and will no doubt fit other P-40 models too. The master part of the seat was 3D designed and printed for the best levels of detail. The US type seat belts are c..

The set contains all new wheels with cross tread tyres, the wheel hubs come as separate casts and the set offers two styles of the wheels, either with the hub covers on or without the covers. 3D designed, 3D-printed master parts...

The new Special Hobby P-40 Warhawk kits will benefit from the addition of this set which offers the modeller new and nicely detailed cockpit sidewalls and a new control stick. The cast part replace directly and easily the original styrene items. Not much surgery needed. The master parts were 3D desi..

Nicely detailed resin ejection seats for reconnaissance and ground-attack versions of the Mirage F.1 model now produced by Special Hobby. The set comes with photo-etched seat harness and other smaller parts...

Meticulously detailed nose and main undercarriage wheels for a French post-war fighter aircraft. Intended in the first place for the new Special Hobby model, can be used for different models as well. Designed using 3D technology...

Full resin kit of an amphibious tracked vehicle. Although initially designed as a combat and reconnaissance vehicle, it was mainly used to transport troops and cargo to other vehicles in the obstructed areas. Thanks to its low weight and wide belts Its capabilities were phenomenal. It was used in Eu..

Resin update set tailored to fit any version of the Hudson. The resin parts are direct replacement of the pilot's seat and cockpit floor. A photo-etched fret offers a new instrument panel and seat belts. The Hudson model is produced by Special Hobby in two boxings and was also reboxed by Italeri and..