1/72 Douglas A-3 Skywarrior Decals
Type: Water-slide decals
1. A-3B (A3D-2) Part: VAH-2, US Navy, 601/NL (BuNo.147650) CVA-43 USS Coral Sea, Gulf of Tonkin, Vietnam Coast, 1965 The plane crashed 6th October 1966 after a collision with RA-5C.
2. EKA-3B Part: 1st Detachment of VAQ-135 "Ravens", US Navy , 610/AB (BuNo.147667) CVA-67 USS John F.Kennedy, 1965 A-3
Skywarrior was the American sailors nicknamed 'whale'. Initially, A-3B. In June 1967 converted to a tanker KA-3B, in July of the same year in the EKA-3B. And in November 1974 back to KA-3B.
3. EKA-3B Part: VAQ-132, US Navy, 614/NG (BuNo.142400) Initially, A-3B. Modified to KA-3B tanker in May 1966 In June 1969, the EKA-3B.
4. A-3B (A3D-2) Part: VAH-13, US Navi, 611/NH (BuNo.142401) Airplane A-3B, squadron VAH-13 - great emblem thereof (bat) is applied on the fuselage. fuselage. The squadron was based on the aircraft carrier CVA-63 USS Kitty Hawk, later replaced these machines planes A-5 Vigilante. In June 1967 the aircraft was modified tanker KA-3B.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
1. A-3B (A3D-2) Part: VAH-2, US Navy, 601/NL (BuNo.147650) CVA-43 USS Coral Sea, Gulf of Tonkin, Vietnam Coast, 1965 The plane crashed 6th October 1966 after a collision with RA-5C.
2. EKA-3B Part: 1st Detachment of VAQ-135 "Ravens", US Navy , 610/AB (BuNo.147667) CVA-67 USS John F.Kennedy, 1965 A-3
Skywarrior was the American sailors nicknamed 'whale'. Initially, A-3B. In June 1967 converted to a tanker KA-3B, in July of the same year in the EKA-3B. And in November 1974 back to KA-3B.
3. EKA-3B Part: VAQ-132, US Navy, 614/NG (BuNo.142400) Initially, A-3B. Modified to KA-3B tanker in May 1966 In June 1969, the EKA-3B.
4. A-3B (A3D-2) Part: VAH-13, US Navi, 611/NH (BuNo.142401) Airplane A-3B, squadron VAH-13 - great emblem thereof (bat) is applied on the fuselage. fuselage. The squadron was based on the aircraft carrier CVA-63 USS Kitty Hawk, later replaced these machines planes A-5 Vigilante. In June 1967 the aircraft was modified tanker KA-3B.
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
| General Info | |
| Scale | 1/72 |
| Type | Model Upgrade/Accessory |
| Subtype | Decals / Stickers |
- Stock: In Stock
- Reward Points: 20
- SKU: PRS72-109
- 1pcs in Stock
Print Scale Decals
MRP: US$17.09 Save: US$3.08
18% OFF
US$14.01
(excl. Tax)
"In-Stock" Really Means It
Combine Shipping & Save
SAME or Next day shipping*
There are no reviews
Maybe you can help? Many users will be grateful to you. And so are we.