1/48 A-10 Thunderbolt II Decals Part 1
Type: Water-slide decals
1. A-10A Nr.74-552, 349th Wing AFRES, 1995.
2. Part: 57th TTW, TAC, USAF Serial: 75-0258. Airplane pilot in camouflage during exercise JAWS 1978.
3. A-1a serial 75-260 flown by the 57th Tactical Training Wing in the ??Jaws ll?? exercise in November 1977.
4. 76-0531 Fairchild A-10A ??Stephanie Anne Bayou Babe??926 TFG/706 TFS "ns", tail code "NO", NAS New Orleans, LA - King
Fahd Airport, Saudi Arabia.
5. 77-0272 Desert Doc A-10A 926 TFG/706 TFS "Cajuns", tail code "NO", NAS New Orleans, LA - King Fahd Airport, Saudi Arabia.
6. A-10A 355th TFS/354th TFW "Falcons", tail code "MB" - Myrtle Beach AFB, SC - King Fahd Airport, Saudi Arabia.
7. 79-0112 Here Comes the Judge A-10A 355th TFS/354th TFW "Falcons", tail code "MB" - Myrtle Beach AFB, SC - King Fahd Airport, Saudi Arabia.
8. 79-0096 Honey Buns - left Wicked Sensation - rigth 61 missions A-10A 353rd TFS/354th TFW "Panthers", tail code "MB" - Myrtle Beach AFB, SC - King Fahd Airport, Saudi Arabia.
9. A-10A 81-0964 was flown by Captain Todd "Shanghai" Sheehy of the 511th TFS in Jan 1991. EE B
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
1. A-10A Nr.74-552, 349th Wing AFRES, 1995.
2. Part: 57th TTW, TAC, USAF Serial: 75-0258. Airplane pilot in camouflage during exercise JAWS 1978.
3. A-1a serial 75-260 flown by the 57th Tactical Training Wing in the ??Jaws ll?? exercise in November 1977.
4. 76-0531 Fairchild A-10A ??Stephanie Anne Bayou Babe??926 TFG/706 TFS "ns", tail code "NO", NAS New Orleans, LA - King
Fahd Airport, Saudi Arabia.
5. 77-0272 Desert Doc A-10A 926 TFG/706 TFS "Cajuns", tail code "NO", NAS New Orleans, LA - King Fahd Airport, Saudi Arabia.
6. A-10A 355th TFS/354th TFW "Falcons", tail code "MB" - Myrtle Beach AFB, SC - King Fahd Airport, Saudi Arabia.
7. 79-0112 Here Comes the Judge A-10A 355th TFS/354th TFW "Falcons", tail code "MB" - Myrtle Beach AFB, SC - King Fahd Airport, Saudi Arabia.
8. 79-0096 Honey Buns - left Wicked Sensation - rigth 61 missions A-10A 353rd TFS/354th TFW "Panthers", tail code "MB" - Myrtle Beach AFB, SC - King Fahd Airport, Saudi Arabia.
9. A-10A 81-0964 was flown by Captain Todd "Shanghai" Sheehy of the 511th TFS in Jan 1991. EE B
How to apply water-slide decals:
1. Preparation: to achieve better result, a gloss or semi-gloss coat is very important. It will make a smooth layer which the decals will suction to and make it much easier to apply and set them.
2. Cut out the decal you need (do it on cutting mat)
3. Grab the decal with tweezers, place it on the surface of the water and leave it for about 20 seconds.
4. Remove the decal from the water and place it on paper towel to remove any excess water.
5. Apply decal solution to the part where the decal is to be placed.
6. Slide the decal off the backing paper on to the model. Using a paint brush or cotton bud is a good way to do this without damaging the decal.
7. Use the brush, knife or cotton bud to position the decal. Using your paper towel, gently dab the decal and soak up the excess water (decal softner is also recommended at this stage. After applying softner, the decal will suction to the part and flatten out smooth.)
8. When the decal is completely dry, give another coat of varnish or Klear/Future to seal it.
| General Info | |
| Scale | 1/48 |
| Type | Model Upgrade/Accessory |
| Subtype | Decals / Stickers |
- Stock: In Stock
- Reward Points: 24
- SKU: PRS48-072
- 1pcs in Stock
Print Scale Decals
MRP: US$20.52 Save: US$4.01
19% OFF
US$16.50
(excl. Tax)
"In-Stock" Really Means It
Combine Shipping & Save
SAME or Next day shipping*
There are no reviews
Maybe you can help? Many users will be grateful to you. And so are we.